| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | SFP-10G-ZR | SFP-10G-SR |
| 2 | Cisco | SFP-10G-ZR-S | SFP-10G-LR |
| 3 | Alcatel-Lucent | SFP-10G-ZR | SFP-10G-LRM |
| 4 | Arista Networks | SFP-10G-ZR | SFP-10G-ER |
| 5 | Huawei | SFP-10G-ZR | |
| 6 | Brocade | 10G-SFPP-ZR | |
| 7 | HPE(H3C) | SFP-10G-ZR | |
| 8 | Cisco Meraki | MA-SFP-10GB-ZR | |
| 9 | Juniper Networks | EX-SFP-10GE-ZR |
| Cisco Compatible | SFP-10G-ZR | Vendor Name | HYTOPTODEVICE |
| Form Factor | SFP+ | Max Data Rate | 10.7Gbps |
| Wavelength | 1550nm | Max Distance | 80km |
| Connector | Duplex LC | Transmitter Type | EML 1550nm |
| Cable Type | SMF | Receiver Type | APD |
| TX Power | 0~+4dBm | Receiver Sensitivity | < -24.0dBm |
| Typical Power Consumption | ≤1.8W | Receiver Overload | -7dBm |
| Bit Error Ratio (BER) | 1E-12 | DDM/DOM | Support |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI | Operation Temperature | 0to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
Fiber Choice: OS1/OS2 single-mode fiber (9/125 µm) is correct. Standard duplex LC-LC connectors are standard. Do NOT use OM1/OM2/OM3/OM4 Multimode Fiber (MMF) cables; severe modal dispersion will prevent link establishment.
Connector Match: Clarify that UPC/PC is required for proper optical contact, while APC will result in an unusable link and excessive signal loss.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Tuning: If auto-negotiation fails with legacy SAN switches, manually lock the port speed to 10Gbps
Handling: Wear an ESD wrist strap during installation. Maintain a minimum fiber bend radius of 30 mm to prevent micro-bends and optical power loss.
Installation & Hot-Swap Rules
Supports MSA-compliant hot-swapping. Insert/remove gently without powering down the device. Keep dust caps on unused LC ports and avoid frequent re-plugging.
Operating Environment
Commercial grade: 0°C to 70°C in indoor environments. Keep away from extreme heat, moisture, and dust for long-term stability.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List and Supported Devices
Lab‑validated with Alcatel‑Lucent customized EEPROM, plug‑and‑play without extra CLI tuning.
• Alcatel‑Lucent 7705 SAR series routers
• Alcatel‑Lucent 7450 ESS series switches
• Alcatel‑Lucent 7210 SAS service switches
• Alcatel‑Lucent OS‑6900 / OS‑10K family
Note:Use latest stable firmware for best compatibility performance.
Technical Warning: When testing or deploying this SFP-10G-ZR 80km module over short distances (typically less than 30km), an optical attenuator (12dB to 15dB) must be used. Failure to attenuate the signal may cause permanent damage to the receiver due to optical overload.
| Distance | ≤ 10km | ≤ 30km | ≤50km | Remarks |
| Attenuator | 15dB | 12dB | 6dB |






Q1: What photodiode detector is used in SFP‑10G‑ZR and why is it delicate? A: It uses an APD avalanche photodiode detector. APD delivers <‑24dBm high sensitivity for 80km links, yet it is easily damaged when incoming power exceeds ‑7dBm overload threshold, always apply proper attenuation for short‑distance deployments.
Q2: How do I determine the exact attenuator value required for an SFP‑10G‑ZR link? A: You can calculate attenuator value from real‑world link loss. With TX output 0~+4dBm, overload‑7dBm and sensitivity<‑24dBm, keep received power between ‑7dBm and ‑24dBm; install fixed attenuator if incoming power goes above‑7dBm.
Q3: What is the optical power budget of an SFP‑10G‑ZR transceiver? A: SFP‑10G‑ZR provides 24 dB optical power budget. Based on 0~+4dBm transmit power and<‑24dBm receiver sensitivity, this budget supports up to 80 km over compliant G.652 single‑mode fiber.
Q4: Can SFP‑10G‑ZR achieve 80 km over legacy OS1 single‑mode fiber? A: Yes, SFP‑10G‑ZR can reach 80 km over legacy OS1 single‑mode fiber. OS1 meets G.652 1550nm specifications; ensure total link loss stays below 24 dB and minimize splice joints for stable operation.
Q5: Can SFP‑10G‑ZR operate over a single fiber strand (BiDi)? A: No, SFP‑10G‑ZR cannot work on single‑strand BiDi fiber. It adopts duplex LC dual‑fiber architecture, separate transmit and receive paths require two single‑mode fiber strands.
Q6: What is Chromatic Dispersion (CD) and why is it a major challenge at 80km? A: Chromatic Dispersion (CD) is optical pulse broadening across fiber. At 80 km 1550nm long‑haul transmission CD distorts 10G signals; the built‑in cooled EML laser mitigates CD for standard G.652 fiber deployments.
Q7: What type of transmitter laser is used in SFP‑10G‑ZR? A: SFP‑10G‑ZR uses a cooled EML electro‑absorption modulated laser. This 1550 nm cooled laser delivers stable output and low chromatic dispersion to satisfy 80 km long‑reach single‑mode transmission requirements.
Q8: Does SFP‑10G‑ZR require Forward Error Correction (FEC)? A: No, SFP‑10G‑ZR does not require mandatory FEC. 10GBASE‑ZR runs native 10G Ethernet without FEC, though enabling device‑level FEC improves link margin under high‑loss fiber conditions.
Q9: How does Polarization Mode Dispersion (PMD) impact 80 km ZR links? A: PMD introduces signal distortion on long‑haul fiber links. For 80 km SFP‑10G‑ZR links deploy low‑PMD G.652 fiber; old high‑PMD fiber increases bit‑error rate and causes intermittent link flapping.
Q10: Will third‑party SFP‑10G‑ZR optics work in Alcatel‑Lucent and other major switch brands? A: Yes, properly EEPROM‑programmed third‑party SFP‑10G‑ZR works on Alcatel‑Lucent and mainstream switch hardware. Custom programmed firmware eliminates transceiver‑unsupported alarms; validate against your device firmware version before field installation.
Q11: Can I connect an SFP‑10G‑ZR directly to an SFP‑10G‑LR or ER transceiver? A: Yes, cross‑model interconnection is technically feasible. SFP‑10G‑ZR high transmit power (0~+4dBm) can overload LR/ER receivers, you must add inline optical attenuator for short‑range mixed‑module links.
Q12: Will using third‑party SFP‑10G‑ZR modules void Alcatel‑Lucent switch hardware warranties? A: Normally third‑party transceivers will not void chassis hardware warranty. Warranty covers original switch hardware itself; only physical damage directly caused by the optical module may affect hardware coverage.
Q13: Can SFP‑10G‑ZR work in server NICs like Intel X520/X710 or Mellanox? A: Yes, SFP‑10G‑ZR is compatible with standard SFP+ server NICs. Confirm NIC firmware supports 10GBASE‑ZR; note some server adapters cannot read DDM data from third‑party optics.
Q14: What laser safety class applies to SFP‑10G‑ZR? A: SFP‑10G‑ZR falls under Class 1 laser safety classification. It is eye‑safe under normal operation; avoid direct eye exposure toward open fiber ports while the module is powered on.
Q15: What certifications should I verify prior to purchasing? A: Validate MSA SFF‑8431, SFF‑8472, RoHS and Class 1 laser safety certifications. Also verify full‑rate aging‑test records and EEPROM programming matching your target network hardware.
Packaging & Custom OEM Solutions
Individually sealed in ESD-safe packaging and ready to ship. We offer tailored OEM solutions—including custom logos and private labeling—to support high-volume distributors,wholesaler and system integrators.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.






