| NO. | Brand | Compatible P/N | Remarks |
| 1 | Cisco | SFP-10G-ZR | |
| 2 | Cisco | SFP-10G-ZR-S | |
| 3 | Alcatel-Lucent | SFP-10G-ZR | |
| 4 | Arista Networks | SFP-10G-ZR | |
| 5 | Huawei | SFP-10G-ZR | |
| 6 | Brocade | 10G-SFPP-ZR | |
| 7 | HPE(H3C) | SFP-10G-ZR | |
| 8 | Cisco Meraki | MA-SFP-10GB-ZR | |
| 9 | Juniper Networks | EX-SFP-10GE-ZR |
10G SFP+ ZR Optical Transceiver Module Compatible Juniper Networks EX-SFP-10GE-ZR (10GBASE-ZR, SMF, 1550nm, 80km, LC, DOM) | HYTOPTODEVICE
HYTOPTODEVICE EX-SFP-10GE-ZR compatible Juniper Networks is a high-performance,hot-pluggable 10GBASE-ZR SFP+ optical transceiver. It supports high-speed 10Gbps data transmission up to 80 kilometers (49.7 miles) over LC Duplex Connector with Single Mode Fiber(SMF). Integrating a cooled EML transmitter and a high-sensitivity APD receiver, this meraki 10gbase-zr optic replacement is specifically designed for long-haul 10-Gigabit Ethernet links within cloud-managed networks. Compliant with both SFP+MSA and IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432. With low latency and low power consumption, the Juniper Networks compatible sfp+ module is ideal for data center, 10G Ethernet and Fibre Channel etc.
Key Technical Specifications of 10G SFP+ ZR
| Juniper Compatible | EX-SFP-10GE-ZR | Vendor Name | HYTOPTODEVICE |
| Form Factor | SFP+ | Max Data Rate | 10.7Gbps |
| Wavelength | 1550nm | Maxmum Transmission Distance | 80km |
| Connector | Duplex LC | Transmitter Type | 1550nm EML |
| Cable Type | SMF | Receiver Type | APD |
| TX Power | 0~+4.5dBm | Receiver Sensitivity | < -23.0dBm |
| Power Consumption | ≤1.5W | Operation Temperature | 0 to 70°C (32 to 158°F) |
Full Compatibility List and Supported Devices of Juniper Networks 10G SFP+ ZR
One of the biggest advantages of HYTOPTODEVICE compatible optical module is the full brand compatibility.Featuring stable plug-and-play performance for 10G Network Switches and industrial standard Compliance for Enterprise-Grade Networks. It helps enterprises cut hardware costs without sacrificing performance. Worried about compatibility? Don't be.hardware verified compability with Cisco,Huawei,Arista,Juniper. We deliver verified results on real module,real hardware. Video proof available upon request. Our juniper 10gbase-zr optic replacement is fully tested and certified to work seamlessly with the following Juniper Networks equipments:
Fixed-Configuration Access & Aggregation: EX3300, EX4300, EX4400, EX4600, and EX4650 Series (e.g., EX4300-48T, EX4600-40F).
Core & Modular Chassis Switches: EX9200 Series modular line cards (e.g., EX9200-40XS).
High-Capacity Campus Backbones: Establishing long-range core-to-core connections across broad university layouts or sprawling industrial manufacturing sites up to 80km apart.
Metropolitan Area Network (MAN) Ring Aggregation: Linking regional corporate hubs, municipal offices, or public sector networks via leased or private dark fiber.
Data Center Interconnect (DCI): Providing the 10Gbps long-haul transport layer required to bridge primary data nodes to offsite disaster recovery setups.
Service Provider Edge Transport: Connecting enterprise customer-premises equipment (CPE) back to regional Juniper aggregation points across long local loops.
Technical Warning: When testing or deploying this SFP-10G-ZR 80km module over short distances (typically less than 30km), an optical attenuator (12dB to 15dB) must be used. Failure to attenuate the signal may cause permanent damage to the receiver due to optical overload.
Q1: Will Junos OS label third-party optic as Non-Juniper and shut down switch port?
A1: No. HYTOPTODEVICE’s Juniper compatible transceivers are preloaded with official Juniper-certified cryptographic signature & original EEPROM data via real hardware programming instead of virtual simulation. Junos OS auto-identifies our optics natively and brings up port links without offline or Non-Juniper warning prompts.
Q2: What Junos CLI command to check real-time DDM optical power readings on Juniper ports?
A2: Run this Junos operational mode CLI command for complete real-time optical diagnostic data of HYTOPTODEVICE installed transceivers: show diagnostics interfaces xe-X/X/X; this command pulls full DOM/DDM metrics including transmit power, receive power and module temperature.
Q3: Do HYTOPTODEVICE Juniper transceivers need "allow unsupported transceiver" manual configuration on Junos?
A3: No configuration modification is required. HYTOPTODEVICE modules replicate factory-standard Juniper EEPROM identity parameters, supporting true plug-and-play on all Junos-powered Juniper hardware; no extra global or interface-level unsupported transceiver permission setup needed.
Q4: Does installing HYTOPTODEVICE third-party compatible optics invalidate official Juniper Care warranty contract?
A4: No. Protected by Magnuson-Moss Warranty Act and global antitrust consumer protection regulations, Juniper cannot void existing Juniper Care warranty solely for using HYTOPTODEVICE compliant compatible transceivers. Juniper engineers only request temporary optic swap for Layer 1 physical fault isolation during troubleshooting, without warranty termination right.
Q5: Is bench testing HYTOPTODEVICE 80km ZR transceiver with only 1m short fiber patch cord allowed without extra accessories?
A5: Never conduct short-loop bench test on HYTOPTODEVICE 80km ZR modules without installing inline fixed optical attenuator. Equipped with high-sensitivity APD internal receiver chip, these ZR transceivers get damaged easily: direct TX-RX short fiber loop via 1m jumper cable causes excessive incoming optical power, permanently saturates and burns the built-in APD optical receiving sensor.
Q6: How much minimum optical attenuation is needed to safeguard APD receiver of HYTOPTODEVICE ZR optics?
A6: HYTOPTODEVICE long-distance ZR transceivers require minimum 14dB~15dB physical link optical attenuation, equivalent to approx. 40km standard single-mode fiber loss. All bench deployments or fiber spans shorter than the equivalent 40km cable must install either 10dB or 15dB LC fixed optical attenuator on the RX receiving path for APD protection.
Q7: What is the full optical power budget specification of HYTOPTODEVICE ZR long-haul transceiver?
A7: HYTOPTODEVICE 80km ZR optical module delivers a minimum 23dB overall optical power budget. Standard TX transmit optical output power falls between 0 ~ +4 dBm, while the module’s APD receiver minimum working sensitivity reaches -23 dBm; all parameters are calibrated and verified via real hardware DDM testing before factory delivery.
Q8: Is HYTOPTODEVICE ZR transceiver compatible with OM3/OM4 Multi-Mode Fiber existing cabling?
A8: HYTOPTODEVICE ZR series transceivers cannot run on OM3 & OM4 multi-mode fiber (MMF). Designed at 1550nm long-haul specific wavelength, the entire optical laser assembly is exclusively optimized for standard 9/125µm Single-Mode Fiber (SMF) network construction only.
Q9: Can HYTOPTODEVICE 80km ZR modules work alongside brand-name original ZR transceivers in the same Juniper chassis?
A9: Yes. All HYTOPTODEVICE ZR transceivers follow industry-standard MSA specifications and complete rigorous interoperability testing. They operate seamlessly mixed with original-brand ZR optics inside identical Juniper equipment, no port negotiation drop or DDM reading abnormality happens under mixed deployment.
Q10: Does HYTOPTODEVICE ZR module support DDM real-time monitoring under Junos OS?
A10: Fully supported. Every HYTOPTODEVICE 80km ZR transceiver is pre-calibrated for DOM/DDM function at factory. Users can view real-time TX/RX power, operating temperature and supply voltage directly via the standard Junos diagnostics CLI command without additional driver or configuration edits.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.
