| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | SFP-10G-ER40 | SFP-10G-SR |
| 2 | Cisco | SFP-10G-ER | SFP-10G-LR |
| 3 | Cisco | SFP-10G-ER-S | SFP-10G-LRM |
| 4 | Cisco Meraki | MA-SFP-10GB-ER | SFP-10G-ZR |
| 5 | Arista Networks | SFP-10G-ER | |
| 6 | HPE Aruba | J9153D | |
| 7 | Brocade | 10G-SFPP-ER40 | |
| 8 | H3C | SFP-XG-ER-SM1550 | |
| 9 | Juniper | EX-SFP-10GE-ER40 | |
| 10 | Dell | GP-10GSFP-1E |
|
Dell Compatible |
GP-10GSFP-1E |
Vendor Name |
HYTOPTODEVICE |
|
Form Factor |
SFP+ |
Max Data Rate |
10.7Gbps |
|
Wavelength |
1550nm |
Max Distance |
40km |
|
Connector |
Duplex LC |
Transmitter Type |
1550nm EML |
|
Cable Type |
SMF |
Receiver Type |
PIN |
|
TX Power |
-1.0~+3.0dBm |
Receiver Sensitivity |
< -15.5dBm |
|
Power Consumption |
≤1.5W |
Operation Temperature |
0 to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
Fiber Choice: OS1/OS2 single-mode fiber (9/125 µm) is correct. Standard duplex LC-LC connectors are standard. Do NOT use OM1/OM2/OM3/OM4 Multimode Fiber (MMF) cables; severe modal dispersion will prevent link establishment.
Connector Match: Clarify that UPC/PC is required for proper optical contact, while APC will result in an unusable link and excessive signal loss.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Tuning: If auto-negotiation fails with legacy SAN switches, manually lock the port speed to 10Gbps
Handling: Wear an ESD wrist strap during installation. Maintain a minimum fiber bend radius of 30 mm to prevent micro-bends and optical power loss.
Installation & Hot-Swap Rules
Supports MSA-compliant hot-swapping. Insert/remove gently without powering down the device. Keep dust caps on unused LC ports and avoid frequent re-plugging.
Operating Environment
Commercial grade: 0°C to 70°C in indoor environments. Keep away from extreme heat, moisture, and dust for long-term stability.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List and Supported Devices
Main Application Scenarios
| Distance | ≤ 5km | ≤ 10km | ≤20km | Remarks |
| Attenuator | 12dB | 9dB | 6dB |






Q1: When do I need an inline optical attenuator for SFP‑10G‑ER? A: You need an inline optical attenuator when link distance is very short below 10km to avoid receiver overload, SFP‑10G‑ER transmit power ranges ‑1 ~ +3dBm, add proper attenuator if received power exceeds 0.5dBm to protect receiver chip.
Q2: What is the typical optical power budget of an SFP‑10G‑ER transceiver? A: The typical optical power budget for SFP‑10G‑ER is around 14dB, it supports maximum 40km over G.652 single‑mode fiber with ‑1 ~ +3dBm transmit and ‑15.5dBm receiver sensitivity.
Q3: Can I use SFP‑10G‑ER with BiDi (Single Strand) fiber cabling? A: No, SFP‑10G‑ER cannot work with BiDi single‑strand fiber, it uses dual‑fiber LC port for separate transmit and receive paths and requires two‑strand SMF for normal operation.
Q4: Can I insert an SFP‑10G‑ER into a standard 1G SFP port? A: No. 1G SFP ports lack the hardware bandwidth and clocking required for 10G SFP+ modules.
Q5: Does SFP‑10G‑ER auto‑negotiate down to 1G speed? A: No, SFP‑10G‑ER does not auto‑negotiate down to 1G, it runs fixed 10G rate only, you must set port speed manually if your switch supports forced‑rate configuration.
Q6: Will using third‑party SFP‑10G‑ER modules void my switch hardware warranty? A: In most cases third‑party SFP‑10G‑ER will not void hardware warranty, hardware warranty covers switch chassis itself, check your vendor legal statement; only module‑caused physical damage voids relevant parts warranty.
Q7: Does SFP‑10G‑ER support DOM / DDM (Digital Optical Monitoring)? A: Yes, our compatible SFP‑10G‑ER fully supports DOM/DDM compliant to SFF‑8472, you can read real‑time Tx power, Rx power, temperature and supply voltage via switch CLI.
Q8: Can I connect SFP‑10G‑ER to an SFP‑10G‑ZR (80km) transceiver? A: Yes, cross‑connection between SFP‑10G‑ER and SFP‑10G‑ZR works, but you must add inline attenuator for short links to prevent receiver damage due to high ZR transmit output power.
Q9: What type of laser is built into an SFP‑10G‑ER transceiver? A: SFP‑10G‑ER uses cooled EML (Electro‑Absorption Modulated Laser) at 1550nm wavelength, EML delivers stable optical output for long‑reach 40km single‑mode fiber transmission.
Q10: Will populating multiple ER transceivers side‑by‑side cause overheating in high‑density switches? A: Side‑by‑side ER modules will not cause overheating with proper chassis airflow, each ER module consumes ≤1.5W power; ensure switch fan works normally and maintain recommended operating temperature 0‑70°C.
Q11: What is the target Bit Error Rate (BER) specification? A: Target BER for SFP‑10G‑ER is 1×10⁻¹² under full operating conditions, this standard meets IEEE 802.3ae requirements for stable 10G Ethernet transmission.
Q12: What receiver technology is used in SFP‑10G‑ER? A: SFP‑10G‑ER adopts PIN‑based receiver technology, it offers good sensitivity of ‑15.5dBm and stable performance for 40km 10GBASE‑ER single‑mode fiber links.
Q13: Does chromatic dispersion affect SFP‑10G‑ER over 40 km? A: Chromatic dispersion has limited impact within 40km for SFP‑10G‑ER EML laser, signal degradation will rise obviously when transmission distance exceeds 40km over G.652 fiber.
Q14: What MSA standards govern SFP‑10G‑ER transceivers? A: SFP‑10G‑ER follows SFF‑8431 SFP+ MSA and IEEE 802.3ae 10GBASE‑ER standards, also complies with SFF‑8472 for digital optical monitoring function.
Q15: How do I verify receiver light levels in the switch CLI before bringing up the interface? A: You can verify receiver light levels by reading DDM DOM values via switch CLI commands, check real‑time Rx power value and confirm it falls within the valid ‑1 ~ ‑15.5dBm working range before enabling the interface.
Q16: Can SFP‑10G‑ER be deployed in dark fiber leases? A: Yes, SFP‑10G‑ER is suitable for dark fiber lease deployment, confirm fiber quality and link loss beforehand, add optical attenuator if excess optical power exists on short dark‑fiber circuits.
Packaging & Custom OEM Solutions
Individually sealed in ESD-safe packaging and ready to ship. We offer tailored OEM solutions—including custom logos and private labeling—to support high-volume distributors,wholesaler and system integrators.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.






