| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | SFP-10G-ER40 | SFP-10G-SR |
| 2 | Cisco | SFP-10G-ER | SFP-10G-LR |
| 3 | Cisco | SFP-10G-ER-S | SFP-10G-LRM |
| 4 | Cisco Meraki | MA-SFP-10GB-ER | SFP-10G-ZR |
| 5 | Arista Networks | SFP-10G-ER | |
| 6 | HPE Aruba | J9153D | |
| 7 | Brocade | 10G-SFPP-ER40 | |
| 8 | H3C | SFP-XG-ER-SM1550 | |
| 9 | Juniper | EX-SFP-10GE-ER40 | |
| 10 | Dell | GP-10GSFP-1E |
HYTOPTODEVICE Cisco SFP‑10G‑ER‑S compatible 10G ER SFP+ TRANSCEIVER serves as drop‑in replacement optic for Cisco Catalyst switches and routers. Pre‑flashed Cisco‑specific EEPROM avoids third‑party transceiver alarms and unexpected link flapping.
This 1550 nm 10GBASE‑ER single‑mode transceiver runs at 10.3125Gbps, supporting max 40 km transmission over OS1/OS2 G.652 SMF. DDM monitoring and hot‑swap capability ensure stable 24/7 network running. Valid TX output:‑1 ~ +3 dBm,Sensitivity<‑15.5dBm. Perfect for Cisco core‑aggregation uplink, inter‑building campus trunk and multi‑site enterprise long‑haul networking. Source bulk 10G ER SFP+ TRANSCEIVER directly from factory to reduce Cisco network upgrade CAPEX.
|
Cisco Compatible |
SFP-10G-ER-S |
Vendor Name |
HYTOPTODEVICE |
|
Form Factor |
SFP+ |
Max Data Rate |
10.7Gbps |
|
Wavelength |
1550nm |
Max Distance |
40km |
|
Connector |
Duplex LC |
Transmitter Type |
1550nm EML |
|
Cable Type |
SMF |
Receiver Type |
PIN |
|
TX Power |
-1.0~+3.0dBm |
Receiver Sensitivity |
< -15.5dBm |
|
Power Consumption |
≤1.5W |
Operation Temperature |
0 to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Full Compatibility List and Supported Devices
Lab‑validated with pre‑programmed Cisco EEPROM profile, this 10G ER SFP+ TRANSCEIVER prevents transceiver unrecognized alerts, port shutdown and link instability, delivering performance matching original SFP‑10G‑ER‑S. Tested for below Cisco hardware platforms:
● Catalyst 9300, 9400, 3850, 3650 series enterprise switches
● Catalyst 4500‑X, 6800 aggregation switches
● ISR 4000 / ASR 1000 series enterprise routers
● Cisco Nexus 9000, 5000 data‑center switches
Note: Upgrade Cisco IOS/IOS‑XE firmware to official stable release for best compatibility performance.
Main Application Scenarios
● Cisco enterprise core‑aggregation long‑haul SMF uplink
● Inter‑building campus 10G fiber trunk across multi‑building premises
● Metro‑area router‑switch long‑distance interconnection
● Existing single‑mode fiber infrastructure 10G bandwidth upgrade
● WAN edge high‑speed fiber transport for Cisco ISR/ASR routers
● Large‑volume cost‑saving replacement procurement for SFP‑10G‑ER‑S modules
Technical Warning: When testing or deploying this 40km single mode fiber module over short distances (typically less than 20km), an optical attenuator (6dB to 9dB) must be used. Failure to attenuate the signal may cause permanent damage to the receiver due to optical overload.
| Distance | ≤ 5km | ≤ 10km | ≤20km | Remarks |
| Attenuator | 12dB | 9dB | 6dB |
Connectivity Solutions(Applications)
1.10GbE Switch-to-Switch Connectivity
2.10G Link for Switch-Switch with Cable Manager
3.10GbE Structured Cabling Interconnect



FAQ
Q1: What fiber distance limits can I expect when deploying this Cisco‑compatible 10G ER SFP+ module?
A: This 10G ER SFP+ TRANSCEIVER delivers maximum 40 km transmission over OS1/OS2 G.652 single‑mode fiber under IEEE 10GBASE‑ER specification. Actual reach will drop when total link attenuation rises from splices or dirty connectors. Buyers planning long‑haul campus deployments should perform optical loss budget calculation before bulk procurement of SFP‑10G‑ER‑S compatible optics.
Q2: Are there risks of receiver damage when deploying ER transceivers over very short fiber spans?
A: Over‑power incident light can potentially damage the PIN photodiode when running very short SMF links without attenuation pad. For links much shorter than 5 km, insert an appropriate fixed optical attenuator to keep receive power within the valid range <‑15.5 dBm ~ +0.5 dBm. System integrators should note this risk when deploying short‑range metro‑fiber projects with high‑output ER transceivers.
Q3: Which optical wavelength is implemented on the SFP‑10G‑ER‑S compatible optic?
A: SFP‑10G‑ER‑S compatible 10G ER SFP+ TRANSCEIVER adopts 1550 nm transmission wavelength for 10GBASE‑ER standard. Compared with 1310 nm LR modules, 1550 nm features lower fiber dispersion for long‑distance single‑mode transport. When you procure replacement transceivers for cross‑building enterprise links, double‑check wavelength matches your existing fiber‑plant design.
Q4: Which fiber connector polish type works best with this 10G ER SFP+ transceiver?
A: This transceiver uses duplex LC‑UPC interface, you must select UPC‑terminated single‑mode patch cords. APC connectors introduce extra return loss, causing increased BER and intermittent link drops. Network contractors ordering bulk fiber jumpers for SFP‑10G‑ER‑S roll‑outs should avoid APC‑type cables in production‑grade enterprise networks.
Q5: How do multiple splices and connector joints affect my long‑reach 10G ER fiber link performance?
A: Each fusion splice adds ~0.1 dB loss, mechanical splices ~0.3 dB, and connector pairs ~0.5 dB. Calculate your total Link Loss Budget: Total Loss = (Distance × Loss/km) + Connectors + Splices. If total loss exceeds ~15 dB, the link will fail. Always measure total optical loss before commissioning long‑haul links. This is critical for ISP and campus‑wide fiber projects when sourcing 10G ER SFP+ TRANSCEIVER in large quantities.
Q6: Can third‑party SFP‑10G‑ER‑S optics operate on multi‑brand network hardware platforms?
A: Our 10G ER SFP+ TRANSCEIVER supports free EEPROM re‑programming for multi‑vendor compatibility. Pre‑flashed Cisco profile works natively on Cisco hardware; re‑flash EEPROM profile for Arista, Juniper or Dell platforms. Some older firmware‑locked devices require pre‑deployment validation. Enterprise procurement teams can submit exact switch model list for free compatibility assessment prior to bulk shipment.
Q7: Can this SFP‑10G‑ER‑S transceiver be inserted into SFP28 or QSFP+ hardware ports?
A: SFP28 ports are backward compatible with SFP+ optics and will run SFP‑10G‑ER at 10G speed. For 40G QSFP+ ports, a QSA (QSFP to SFP Adapter) is required. Mis‑configuration or missing adapters results in no‑link or link‑flapping conditions. Data‑center technicians should verify port‑speed mode and adapter requirements when mixing 10G ER optics inside higher‑rate switch hardware.
Q8: What troubleshooting steps resolve Cisco unsupported‑transceiver alerts for aftermarket ER modules?
A: First confirm we have shipped units with Cisco‑specific EEPROM. For Cisco IOS‑XE, you may enter service unsupported‑transceiver CLI command to override restriction, though pre‑programmed profile eliminates this requirement in most cases. Also upgrade IOS‑XE to stable release and clean LC connectors. Network engineers troubleshooting third‑party transceiver alarms on Catalyst hardware should follow this standardized workflow.
Q9: Will this compatible SFP‑10G‑ER‑S optic function with common server SFP+ network interface cards?
A: This 10G ER SFP+ TRANSCEIVER works with standard SFP+ NICs from Intel, Broadcom and NVIDIA/Mellanox, after adjusting EEPROM profile if required. Certain NIC firmware may reject unrecognized vendor‑IDs. IT teams building storage‑network infrastructure can request sample units for lab validation before large‑volume server‑NIC related bulk orders.
Q10: Is it acceptable to pair SFP‑10G‑ER‑S transceivers against SFP‑10G‑LR modules on opposite link ends?
A: Physical link can come up, yet mismatched transmit power levels create high risk of over‑driving receiver or insufficient optical margin. 10GBASE‑LR uses 1310 nm while ER uses 1550 nm; single‑mode fiber passes both wavelengths but optical budget does not align. Avoid mixing ER and LR transceivers on production links. Solution architects designing enterprise fiber topologies should deploy matched transceiver pairs for every fiber‑path.
Q11: What is the actual power draw rating for our SFP‑10G‑ER‑S compatible 10G ER SFP+ unit?
A: Maximum power consumption for our SFP‑10G‑ER‑S compatible 10G ER SFP+ TRANSCEIVER is ≤1.5 W per unit. High‑density full‑port deployment creates predictable thermal load for switch chassis. When calculating power and cooling budget for data‑center refresh projects, system planners should factor in per‑module power draw for bulk‑ordered 10G ER SFP+ transceivers.
Q12: What operating temperature range applies to these commercial‑grade SFP‑10G‑ER‑S transceivers?
A: Commercial‑grade version supports 0 ℃ ~ +70 ℃ operating temperature. This variant fits typical indoor enterprise data‑center and campus cabinet environments. For outdoor cabinet or industrial‑grade deployment, you need industrial‑temperature extended‑range modules. Purchasers for harsh‑environment sites need to specify industrial temp‑grade requirement at RFQ stage.
Q13: Does this 10G ER SFP+ transceiver implement hardware‑based FEC function on‑module?
A: This 10G ER SFP+ TRANSCEIVER follows IEEE 10GBASE‑ER standard without hardware‑on‑module FEC. You may enable switch‑ASIC‑based FEC on host‑port if your switch platform supports this function. FEC helps compensate marginal link‑budget for loss‑heavy fiber routes. Network planners for long‑reach metro links should clarify FEC support requirements while submitting procurement requests.
Q14: Can hot‑swap operations be performed for the SFP‑10G‑ER‑S without host device power‑off?
A: Yes, fully MSA‑compliant hot‑swap capability. You can insert or remove the 10G ER SFP+ TRANSCEIVER without powering‑down host equipment. Brief 1‑3‑second link fluctuation occurs during swap; perform replacement inside maintenance window for production‑critical circuits. Datacenter operation teams stocking spare ER transceivers benefit greatly from hot‑swap functionality for live‑network troubleshooting.
Q15: What is the valid laser transmit power window for SFP‑10G‑ER‑S compatible hardware?
A: Per 10GBASE‑ER standard, transmitter output power ranges from ‑1 dBm to +3 dBm. DDM DOM monitoring on Cisco IOS allows real‑time reading of laser transmit power. Gradual power drift indicates end‑of‑life risk for EML laser. Network operation staff monitoring large‑scale transceiver fleets can leverage DDM telemetry for predictive hardware replacement planning.
Packaging & Custom OEM Solutions
Individually sealed in ESD-safe packaging and ready to ship. We offer tailored OEM solutions—including custom logos and private labeling—to support high-volume distributors,wholesaler and system integrators.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.






