| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | SFP-10G-SR | SFP-10G-SR(Alcatel) |
| 2 | Cisco | SFP-10G-SR-S | SFP-10G-LR |
| 3 | Cisco | SFP-10G-SR-X | SFP-10G-LRM |
| 4 | Cisco | SFP-10G-SR-I | SFP-10G-ER |
| 5 | Arista Networks | SFP-10G-SR | SFP-10G-ZR |
| 6 | Brocade | 10G-SFPP-SR | |
| 7 | Huawei | SFP-10G-USR | |
| 8 | HP Procurve | J9150A |
The Difference:SFP-10G-SR vs SFP-10G-SR-S vs SFP-10G-SR-X vs SFP-10G-SR-I
Key Technical Specifications
|
Cisco Compatible |
SFP-10G-SR-X |
Vendor Name |
HYTOPTODEVICE |
| Form Factor | SFP+ | Max Data Rate | 10.7Gbps |
| Wavelength | 850nm | Max Distance | 300m on OM3 |
| Connector | Duplex LC | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -6.5~-0.5dBm | Receiver Sensitivity | < -10.5dBm |
| Power Consumption | ≤1W | Operation Temperature | -5 to 85°C (23 to 185°F) |
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC Multimode Fiber (MMF) — OM3 / OM4 (50/125 µm). Do NOT use SMF.
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Set speed to 10Gbps Full Duplex. Lock speed manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules: MSA hot-swappable. Insert/remove gently without powering down.
Environment:Extended operating temperature (-5°C to 85°C). Avoid extreme heat, moisture, and dust.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Main Application Scenarios
• Short‑reach leaf‑spine inter‑switch connections for Cisco data centers & rugged equipment cabinets
• 10G access‑aggregation trunk expansion for Cisco enterprise networks, bulk project deployment
• 10G ToR switch uplinks for virtualization and server clusters with wide‑temperature requirement
• Intra‑building campus 10G multimode fiber transmission for non‑climate‑controlled cabinet sites
• 40G‑to‑10G migration via QSFP+ 4×10G breakout cables for wholesale network refresh projects
• Multi‑vendor hybrid Cisco enterprise infrastructure deployment for large‑quantity purchase













FAQ
Q1: Can this extended‑temp 10G SFP+ SR‑X optic run on different brands of network hardware?
A: YES. It follows MSA multirate standards and supports Cisco, Arista, Juniper, Dell. Share your switch model and firmware for pre-adaptation when sourcing multi-brand compatible 10G SFP+ SR optics from our transceiver sfp 10g sr supplier.
Q2: Will mixing this 10G multirate module with legacy 1G SFP‑SX optics establish a functional fiber link?
A: NO. Rate mismatch prevents link up. Use matched-speed modules on both ends for extended temperature 10G SFP SR modules supplied by our transceiver sfp 10g sr supplier.
Q3: Does installing third‑party SFP‑10G‑SR‑X optics void my network hardware manufacturer warranty?
A: NO. Hardware warranty stays valid unless module damages the port. We provide test reports for bulk orders of rugged 10G SFP+ SR transceivers from our transceiver sfp 10g sr supplier.
Q4: What is the proper handling for transceiver‑unsupported alerts appearing on Cisco rugged‑series switches?
A: Avoid forcing alarm bypass. Choose our pre-flashed Cisco-X EEPROM version for zero-alarm operation for pre-coded 10G SFP SR optics from our transceiver sfp 10g sr supplier.
Q5: Can I retrieve real‑time optical working metrics from this SFP‑10G‑SR‑X multirate transceiver?
A: YES. DDM is supported to monitor power and temperature. Check switch firmware if data fails to display for DDM-enabled 10G SFP+ SR optics from our transceiver sfp 10g sr supplier.
Q6: Which fiber types are suitable to deploy alongside the SFP‑10G‑SR‑X multirate optical module?
A: Multimode fiber only. 300m on OM3, 400m on OM4. OM4 is recommended for new cabling projects for wholesale 10G SFP SR transceivers from our transceiver sfp 10g sr supplier.
Q7: Am I allowed to deploy this multimode‑optimized 10G transceiver over single‑mode fiber infrastructure?
A: NO. 850nm VCSEL cannot work over single-mode fiber. Select LR modules for single-mode links from our transceiver sfp 10g sr supplier.
Q8: What is the operational light‑emitting wavelength of the Cisco‑compatible SFP‑10G‑SR‑X?
A: 850nm, Class 1 laser. Pair matching 850nm SR modules and monitor laser health via DDM for wide temp 10G SFP SR optics from our transceiver sfp 10g sr supplier.
Q9: What physical fiber connector interface does SFP‑10G‑SR‑X extended‑temp transceiver adopt?
A: Duplex LC-UPC. Do not mix APC connectors and avoid reversed polarity for LC interface 10G SFP+ SR transceivers from our transceiver sfp 10g sr supplier.
Q10: Is the SFP‑10G‑SR‑X multirate transceiver compatible with OM5 wide‑band multimode patch cords?
A: YES. OM5 works with this module, max reach remains 400m for OM5 compatible 10G SFP SR transceivers from our transceiver sfp 10g sr supplier.
Q11: How much electrical power will this wide‑temperature 10G SFP+ SR‑X consume under full‑load traffic?
A: ≤1.0W, low power for high-density ports. Monitor temperature via DDM for low-power 10G SFP+ SR modules from our transceiver sfp 10g sr supplier.
Q12: What temperature operating profiles are offered for this compatible SFP‑10G‑SR‑X optical part?
A: -5~85℃ extended temp in stock; -40~85℃ industrial grade available on custom order for wide range temp 10G SFP SR optics from our transceiver sfp 10g sr supplier.
Q13: Can this rugged‑rated multirate optic satisfy data‑center‑grade bit‑error‑rate performance requirements?
A: YES, BER ≤1×10⁻¹², compliant with IEEE 802.3ae. Burn-in test is available for data center grade 10G SFP SR transceivers from our transceiver sfp 10g sr supplier.
Q14: Can this SFP‑10G‑SR‑X maintain full bidirectional line‑rate under its supported multirate working modes?
A: YES, supports 9.95–11.31Gbps multirate. Confirm your Cisco firmware supports this profile before bulk purchase of multirate 10G SFP SR modules from our transceiver sfp 10g sr supplier.
Q15: What network symptoms will appear once incoming optical signal falls below module receiving sensitivity?
A: Link instability or link down. Inspect fiber, connectors and laser when Rx power is too low for extended temp 10G SFP+ SR transceivers from our transceiver sfp 10g sr supplier.
Packaging & Custom OEM Solutions
Every 10G SFP+ module comes individually sealed in standard anti-static (ESD-safe) packaging, pre-stocked and ready for immediate shipment. For bulk orders, we offer custom OEM packaging—including logo printing and private labeling—tailored for network distributors, system integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



