| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | SFP-10G-SR | SFP-10G-SR(Alcatel) |
| 2 | Cisco | SFP-10G-SR-S | SFP-10G-LR |
| 3 | Cisco | SFP-10G-SR-X | SFP-10G-LRM |
| 4 | Cisco | SFP-10G-SR-I | SFP-10G-ER |
| 5 | Arista Networks | SFP-10G-SR | SFP-10G-ZR |
| 6 | Brocade | 10G-SFPP-SR | |
| 7 | Huawei | SFP-10G-USR | |
| 8 | HP Procurve | J9150A |
The Difference:SFP-10G-SR vs SFP-10G-SR-S vs SFP-10G-SR-X vs SFP-10G-SR-I
Key Technical Specifications
|
Cisco Compatible |
SFP-10G-SR-S |
Vendor Name |
HYTOPTODEVICE |
| Form Factor | SFP+ | Max Data Rate | 10.7Gbps |
| Wavelength | 850nm | Max Distance | 300m on OM3 |
| Connector | Duplex LC | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -6.5~-0.5dBm | Receiver Sensitivity | < -10.5dBm |
| Power Consumption | ≤1W | Operation Temperature | 0 to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC Multimode Fiber (MMF) — OM3 / OM4 (50/125 µm). Do NOT use SMF.
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Set speed to 10Gbps Full Duplex. Lock speed manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules: MSA hot-swappable. Insert/remove gently without powering down.
Environment:Commercial grade (0°C to 70°C). Avoid extreme heat, moisture, and dust.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
HYTOPTODEVICE 10G SFP+ SR‑S modules follow Cisco SFP‑10G‑SR‑S S‑Class specification. Pre‑programmed Cisco‑specific EEPROM enables plug‑and‑play. Real‑machine testing avoids identification errors, negotiation failures and link flapping.
Validated Cisco Platforms:
• Cisco Nexus 9300 / 9200 Series Data‑Center Switches
• Cisco Catalyst 9300 / 9400 Enterprise Switches
• Cisco Nexus 3000 Series High‑performance Switches
• All Cisco hardware supporting S‑Class SFP+ 10GBASE‑SR ports
Main Application Scenarios
• Short‑reach leaf‑spine inter‑switch connections for Cisco data centers
• 10G access‑aggregation trunk expansion for Cisco enterprise networks
• 10G ToR uplinks for virtualization and server clusters
• Intra‑building campus 10G multimode fiber transmission
• 40G‑to‑10G migration via QSFP+ 4×10G breakout cables
• Multi‑vendor hybrid Cisco enterprise infrastructure deployment
Connectivity Solutions(Applications)









FAQ
Q1: Will this SFP‑10G‑SR module work with my specific switch brand (e.g., Cisco, Arista, Juniper, Dell)?A: YES. This SFP‑10G‑SR‑S follows MSA standards and has passed real‑machine validation for Cisco Nexus / Catalyst, Arista, Juniper and Dell PowerSwitch; Cisco platforms require S‑Class EEPROM profile while other brands use generic MSA firmware, select pre‑flashed Cisco S‑Class EEPROM version for Cisco switches, choose generic MSA build for other hardware, and provide exact switch model plus firmware version before ordering for pre‑adaptation.
Q2: Is SFP‑10G‑SR backward compatible with 1G SFP‑SX transceivers? A: NO. It is only mechanically pluggable; SFP‑10G‑SR‑S runs at 10.3125Gbps versus 1.25Gbps for SFP‑SX with mismatched optical modulation and bit‑rate, deploy same‑speed transceivers on both link ends, use paired 1G SFP‑SX for 1G links, and note port auto‑negotiation cannot fix optical‑layer rate mismatch.
Q3: Will third‑party or generic SFP‑10G‑SR modules void my equipment warranty? A: NO. Most vendors do not void full device warranty merely for third‑party optics, though damages caused by the third‑party module itself are excluded from OEM coverage; switch hardware defects remain covered but port damage from incompatible optics may be rejected, use HYTOPTODEVICE validated modules, retain purchase records and remove third‑party optics before RMA, and request project test reports for strict enterprise compliance reviews.
Q4: How can I bypass the "unsupported transceiver" error on my switch? A: NOT RECOMMENDED to bypass via switch commands. Cisco S‑Class switches enforce strict EEPROM checks and CLI alarm‑masking only hides warnings with potential port instability risk, order pre‑programmed Cisco S‑Class EEPROM modules for native zero‑alarm operation, use alarm‑masking only for temporary lab testing, and upgrade switch firmware to official stable release to reduce identification failures.
Q5: Does this transceiver support DOM / DDM (Digital Optical Monitoring)? A: YES. It fully complies with SFF‑8472 specification and reads real‑time transmit power, receive power, module temperature and supply voltage with standard measurement accuracy, pull DDM metrics from switch CLI for proactive link health checks, configure optical‑power threshold alerts, and verify switch firmware supports SFF‑8472 if DDM data cannot be retrieved.
Q6: What type of fiber cable does SFP‑10G‑SR require? A: Multimode fiber ONLY. It reaches 300 m over OM3 MMF, 400 m over OM4 MMF; OM1 / OM2 delivers heavily reduced distance and is not recommended for 10GBASE‑SR, deploy OM4 for new cabling or OM3 for existing infrastructure, maintain proper fiber bend radius, and never exceed rated distance to avoid high BER and link flapping.
Q7: Can I use Single‑Mode Fiber (SMF) with an SFP‑10G‑SR module? A: NO. Its 850 nm VCSEL is designed for multimode fiber and suffers extreme signal attenuation over SMF with no usable optical signal, select 10GBASE‑LR SFP+ transceivers for single‑mode cabling environments, and avoid mode‑conversion patch cords which introduce random packet‑loss risks.
Q8: What laser wavelength does the SFP‑10G‑SR operate on? A: 850 nm. Center wavelength is 850 nm within 840‑860 nm window with Class 1 laser safety rating, deploy matching 850 nm SR‑series transceivers on both link ends, avoid direct eye exposure to open optical ports, and track transmit power via DDM to detect laser degradation.
Q9: What optical connector interface does the SFP‑10G‑SR use? A: Duplex LC‑UPC. It features separated TX/RX channels with minimum 500 mating cycles, use matching LC‑UPC patch cords and do not mix APC end‑faces, clean fiber end‑faces before insertion, and prevent reversed TX‑RX polarity which causes no‑link status.
Q10: Can SFP‑10G‑SR support OM5 lime‑green fiber cabling? A: YES. OM5 is backward‑compatible with 850 nm signals and the module max reach stays at 400 m (OM4 performance level), deploy this transceiver directly onto OM5 cabling systems, and note OM5 provides benefits mainly for short‑wave WDM without extra distance gain for standard 10GBASE‑SR.
Q11: What is the maximum power consumption of an SFP‑10G‑SR transceiver? A: ≤1.0 W. This low‑power S‑Class optic draws maximum 1.0 W under full‑load traffic, plan thermal budget ≤1 W per port for high‑density full‑port deployment, keep default switch fan profiles to avoid overheating, and watch module temperature via DDM for thermal anomaly alerts.
Q12: What operating temperature ranges are available? A: Commercial grade 0 ℃ ~ +70 ℃ (stock); industrial grade ‑40 ℃ ~ +85 ℃ (custom‑order only). Commercial units fit standard indoor data‑center rooms, submit custom requests before bulk orders for outdoor or industrial cabinet usage, and keep commercial‑grade modules within rated temperature range to prevent higher BER and shortened laser life.
Q13: Does SFP‑10G‑SR support Bit Error Rate (BER) requirements for data centers? A: YES. Factory‑tested BER ≤1×10⁻¹² and fully compliant with IEEE 802.3ae 10GBASE‑SR standards, reserve adequate optical power budget during link design, keep receive power far above sensitivity threshold via DDM monitoring, and run long‑duration traffic burn‑in tests for project acceptance.
Q14: Can this module sustain full 10Gbps throughput bidirectionally? A: YES. Both TX and RX channels run full 10.3125Gbps line‑rate; S‑Class profile supports Ethernet‑only and FCoE is NOT supported, force switch port speed to fixed 10G instead of relying on auto‑negotiation, execute bidirectional full‑rate traffic validation tests, and select non‑S‑Class SFP‑10G‑SR if you require FCoE storage‑traffic capability.
Q15: What happens if the receiver optical power drops below the threshold? A: Link instability or link down will occur. Typical receive sensitivity ≤‑12.5 dBm; BER rises sharply once below this threshold and complete link failure may follow, continuously monitor Rx power with DDM, troubleshoot high fiber loss, dirty end‑faces, faulty patch cords or laser aging, clean connectors, replace jumpers, shorten distance or pick longer‑reach optics when total link loss exceeds budget.
Packaging Options & Custom‑Packaging Solutions
Every 10G transceiver module gets reliable ESD‑safe packaging out of the box. Standard packing is ready for immediate shipment, while custom‑printed packaging with your logo is available for bulk orders.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



