| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Alcatel-Lucent | SFP-10G-SR | SFP-10G-SR(Cisco) |
| 2 | Cisco Meraki | MA-SFP-10GB-SR | SFP-10G-LR |
| 3 | D-Link | DEM-431XT | SFP-10G-LRM |
| 4 | Dell | GP-10GSFP-1S | SFP-10G-ER |
| 5 | Juniper | SRX-SFP-10GE-SR | SFP-10G-ZR |
| 6 | H3C | SFP-XG-SX-MM850-A | |
| 7 | IBM | 46C3447 | |
| 8 | EdgeCore | ET5402-SR |
|
Juniper Compatible |
SRX‑SFP‑10GE‑SR |
Vendor Name |
HYTOPTODEVICE |
| Form Factor | SFP+ | Max Data Rate | 10.7Gbps |
| Wavelength | 850nm | Max Distance | 300m on OM3 |
| Connector | Duplex LC | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -6.5~-0.5dBm | Receiver Sensitivity | < -10.5dBm |
| Power Consumption | ≤1W | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC Multimode Fiber (MMF) — OM3 / OM4 (50/125 µm). Do NOT use SMF.
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Set speed to 10Gbps Full Duplex. Lock speed manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules: MSA hot-swappable. Insert/remove gently without powering down.
Environment: Commercial temperature (0°C to 70°C). Avoid extreme heat, moisture, and dust.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Main Application Scenarios
• 10G fiber uplink for Juniper SRX firewall to data center switches
• Rack-to-rack short-range interconnection inside server rooms
• Enterprise campus 10G multimode fiber networking
• Virtualization cluster and SAN storage short-distance links
• Bulk supply of Juniper compatible SFP-10G-SR transceiver for global buyers via our SFP-10G-SR 10GBASE-SR SFP module supply













FAQ
Q1: Can this 10G SR SFP+ run on non‑SRX Juniper devices as well as other brand network gear?
A: Yes, it follows SFP+ MSA specs. Custom EEPROM supports SRX; EX/QFX or third-party gear may have transceiver lock limits. Send device model for pre-sales compatibility check when sourcing cross-brand 10GBASE-SR optics from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q2: If I purchase third‑party optics for Juniper SRX, will it void my device hardware warranty?
A: It will not automatically void warranty. Damage caused by defective optics may be excluded. Our modules pass full stress testing, test reports available for large SRX-SFP-10GE-SR replacement orders from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q3: Am I able to deploy this optic inside Intel or Broadcom based server network adapters?
A: Compatible with Intel X520/X710 and Broadcom NetXtreme SFP+ NICs. Some NIC firmware blocks non-OEM optics. We provide generic profile variants for server NIC bulk procurement of Juniper compatible 10G SR transceivers from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q4: What actual working distances can I get deploying old‑generation OM1 and OM2 multimode fiber?
A: OM1 reaches ~33m, OM2 ~82m only. These short distances are not ideal for security networks. OM3/OM4 is recommended for full reach for bulk 10G SR SFP+ purchase projects supported by our SFP-10G-SR 10GBASE-SR SFP module supply.
Q5: What kind of physical connector does this Juniper‑compatible 10G SR SFP+ transceiver adopt?
A: Duplex LC-UPC connector, standard for enterprise 10G multimode security networking. Avoid APC patch cords to prevent extra return loss for transceivers supplied by our SFP-10G-SR 10GBASE-SR SFP module supply.
Q6: Is splitting a 40G QSFP+ SR4 port into four independent 10G SR channels achievable?
A: Yes, with 40G to 4×10G SR4 breakout cable. Enable breakout mode on CLI; wrong settings cause link loss in Juniper security fabrics built with optics from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q7: How much extra latency will be added by a complete 10G SR SFP+ multimode fiber link?
A: Transceiver latency is 10–30ns. End-to-end latency mainly comes from ASIC and fiber propagation. This optic suits gateways and virtualization workloads; test onsite for ultra-low latency projects using our SFP-10G-SR 10GBASE-SR SFP module supply.
Q8: Compare thermal output between optical 10G SR SFP+ and copper 10GBASE‑T SFP+ modules?
A: 10G SR ≤1W, while 10GBASE-T copper consumes 2.5–4W. Optical modules reduce cabinet cooling pressure for high-density SRX racks during bulk roll-out from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q9: Does this Juniper‑compatible 10G SR SFP+ include built‑in hardware FEC function?
A: No onboard hardware FEC, matching IEEE 10GBASE-SR. Turn on FEC at switch/firewall ASIC side if needed. Keep link loss within optical budget for 10GBASE-SR modules from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q10: Can I insert and remove this SFP+ optic without shutting down Juniper SRX firewalls?
A: Yes, it supports SFP+ hot-plug. Avoid frequent swapping during heavy traffic; schedule maintenance windows for bulk module replacement when ordering from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q11: What is the realistic expected working lifespan for SRX‑SFP‑10GE‑SR replacement 10G SR SFP+?
A: MTBF over 1,000,000 hours under 0–70℃. Good ventilation helps extend service life for long-term Juniper security infrastructure purchased via our SFP-10G-SR 10GBASE-SR SFP module supply.
Q12: Does this aftermarket replacement optic follow official SFP+ MSA industry specifications?
A: Fully compliant with SFP+ MSA and SFF-8472 DDM standards. Only EEPROM ID data is customized for Juniper, all electrical and mechanical specs stay standard for third-party 10G SR SFP+ from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q13: What negative impacts will dirty fiber connector ends bring to 10G multimode security links?
A: Dirty LC-UPC ends cause high insertion loss, random packet loss and intermittent link flapping. Add connector cleaning to regular maintenance for Juniper SRX networks deployed with our SFP-10G-SR 10GBASE-SR SFP module supply.
Q14: Why do generic no‑brand 10G SR SFP+ modules show big performance gaps when users buy them?
A: Cheap generic optics use unqualified lasers with high BER risk and short lifespan. HYTOPTODEVICE uses Grade A VCSEL-PIN and aging testing for reliable enterprise bulk procurement of 10GBASE-SR optics from our SFP-10G-SR 10GBASE-SR SFP module supply.
Q15: Are there laser safety hazards while looking into live transmitting port of active 10G SR SFP+?
A: Yes. Though Class 1 laser, invisible 850nm IR light can harm retinas. Never look into powered optical ports on running Juniper SRX hardware using transceivers from our SFP-10G-SR 10GBASE-SR SFP module supply.
Packaging & Custom OEM Solutions
Every 10G SFP+ SR module comes individually sealed in standard anti-static (ESD-safe) packaging, pre-stocked and ready for immediate shipment. For bulk orders, we offer custom OEM packaging—including logo printing and private labeling—tailored for network distributors, system integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



