| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Alcatel-Lucent | SFP-10G-SR | SFP-10G-SR(Cisco) |
| 2 | Cisco Meraki | MA-SFP-10GB-SR | SFP-10G-LR |
| 3 | D-Link | DEM-431XT | SFP-10G-LRM |
| 4 | Dell | GP-10GSFP-1S | SFP-10G-ER |
| 5 | Juniper | SRX-SFP-10GE-SR | SFP-10G-ZR |
| 6 | H3C | SFP-XG-SX-MM850-A | |
| 7 | IBM | 46C3447 | |
| 8 | EdgeCore | ET5402-SR |
|
D-Link Compatible |
DEM-431XT |
Vendor Name |
HYTOPTODEVICE |
| Form Factor | SFP+ | Max Data Rate | 10.7Gbps |
| Wavelength | 850nm | Max Distance | 300m on OM3 |
| Connector | Duplex LC | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -6.5~-0.5dBm | Receiver Sensitivity | < -10.5dBm |
| Power Consumption | ≤1W | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC Multimode Fiber (MMF) — OM3 / OM4 (50/125 µm). Do NOT use SMF.
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Set speed to 10Gbps Full Duplex. Lock speed manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules: MSA hot-swappable. Insert/remove gently without powering down.
Environment: Commercial temperature (0°C to 70°C). Avoid extreme heat, moisture, and dust.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
● D-Link DXS-1210 / DXS-3400 / DXS-4600 Series 10G Core Switches
● D-Link DGS-3630 / DGS-3130 Series Enterprise Aggregation Switches
● D-Link DXS-5000 Series Data Center Switches
Minimum supported firmware: D-Link latest stable firmware release
Main Application Scenarios
● 10G short-reach fiber uplinks for D-Link DXS and DGS series switching stacks
● Data center rack-to-rack multimode fiber interconnections
● Enterprise campus aggregation and core layer uplink connections
● HPC clusters and storage area network short-distance interlinks
● Direct factory supply of D-Link DEM-431XT transceivers for global buyers via our 10g sfp+ transceiver manufacturer









FAQ
Q1: Will this SFP‑10G‑SR module work with my specific switch brand (e.g., Cisco, Arista, Juniper, Dell)? A: This 10G SR SFP+ adheres to SFP+ MSA mechanical and electrical specifications. Custom‑EEPROM delivers stable recognition on D‑Link validated hardware. For other brands, partial devices carry transceiver‑lock restrictions, check host firmware before bulk purchasing. Provide exact switch model for pre‑sales compatibility validation.
Q2: Will third‑party or generic SFP‑10G‑SR modules void my equipment warranty? A: Qualified third‑party 10G SR SFP+ transceivers will not automatically void hardware warranty. Vendors may reject warranty coverage if hardware damage is directly caused by defective optics. Our modules pass full‑stress factory testing to minimize failure risk; preserve test records for enterprise audit for large‑volume DEM‑431XT replacement orders.
Q3: Will this module work in Network Interface Cards (NICs) like Intel or Broadcom? A: Yes, compatible with mainstream Intel X520/X710 and Broadcom NetXtreme SFP+ NIC adapters. Some server NIC firmware blocks non‑OEM optics. We can supply generic‑profile variant, confirm NIC firmware version ahead of large‑scale server NIC deployment.
Q4: How far can SFP‑10G‑SR reach using legacy OM1 or OM2 fiber? A: Legacy OM1/OM2 multimode fiber lacks sufficient modal bandwidth for 10GBASE‑SR. OM1 delivers approx 33m, OM2 around 82m only. Such short distances rarely satisfy campus‑network requirements. Deploy OM3 or OM4 multimode fiber to achieve full‑spec reach for bulk 10G SR SFP+ projects.
Q5: What optical connector interface does the SFP‑10G‑SR use? A: This D‑Link compatible 10G SR SFP+ adopts duplex LC‑UPC connector, widely‑adopted interface for enterprise 10G multimode networking. Avoid APC‑angled‑end‑face patch cords; APC introduces extra return loss and raises bit‑error rate for UPC‑calibrated transceivers.
Q6: Can I break out a 40G QSFP+ SR4 port to four 10G SFP‑10G‑SR modules? A: Achievable with passive 40G‑to‑4×10G SR4 breakout cable. Each breakout lane connects to one independent 10G SR SFP+. Remember to enable breakout mode in switch CLI; misconfigured port settings cause complete link loss inside mixed‑speed D‑Link fabrics.
Q7: What latency should I expect from an SFP‑10G‑SR connection? A: Native transceiver latency stays 10‑30ns per unit. End‑to‑end link latency is dominated by switch ASIC processing and fiber propagation delay. This 10G SR SFP+ brings negligible overhead, suitable for campus and virtualization workloads. Run real‑environment tests for ultra‑low‑latency production scenarios.
Q8: How does heat output compare between SFP‑10G‑SR and 10G copper RJ45 optics? A: 10G SR SFP+ max power ≤1.0W, while 10GBASE‑T copper SFP+ consumes 2.5‑4W per port. Mass copper‑module deployment increases cabinet PUE and cooling burden. For high‑density D‑Link switch racks, choose optical 10G SR SFP+ to ease thermal pressure during large‑volume roll‑out.
Q9: Does SFP‑10G‑SR support FEC (Forward Error Correction)? A: No built‑in hardware FEC on module, matches official IEEE 10GBASE‑SR definition. If error correction is required, activate ASIC‑level FEC on your switch side. Keep link loss within optical‑budget scope to maintain BER ≤1×10⁻¹²; do not compensate poor fiber quality relying on missing transceiver FEC.
Q10: Does SFP‑10G‑SR support hot‑swapping? A: Yes, conforms to SFP+ MSA hot‑plug standard. Insert or remove 10G SR SFP+ without power‑cycling D‑Link switches. Skip frequent hot‑swap during heavy‑traffic business hours, brief link interruption occurs during replacement. Arrange maintenance window for mass module swap‑out.
Q11: What is the average lifespan (MTBF) of an SFP‑10G‑SR module? A: Calculated MTBF over 1,000,000 hours under 0‑70℃ clean cabinet operating conditions. Actual service life is affected by cabinet temperature, vibration and repeated hot‑swap cycles. Maintain good rack ventilation to extend service life for long‑term D‑Link campus infrastructure.
Q12: Does the transceiver comply with MSA (Multi‑Source Agreement) standards? A: Fully compliant with SFP+ MSA and SFF‑8472 DDM monitoring standards. D‑Link customized EEPROM only modifies identification information; mechanical dimension, electrical signal and monitoring functions strictly follow MSA specification for third‑party replacement 10G SR SFP+.
Q13: How do dust and dirt affect SFP‑10G‑SR performance? A: Dust and stains on LC‑UPC end‑faces are top trigger for unstable 10G links. Contamination raises insertion loss, triggers random packet loss and intermittent link flapping even with link‑up status. Add optical‑connector cleaning into regular maintenance workflow for D‑Link enterprise networks.
Q14: Are all generic SFP‑10G‑SR optics built with the same internal components? A: Not at all. Low‑cost generic 10G SR SFP+ use unqualified laser chips with insufficient screening, bringing higher bit‑error risk and shorter lifetime. HYTOPTODEVICE uses grade‑A VCSEL‑PIN components plus multi‑stage aging testing, more reliable for enterprise‑scale bulk procurement.
Q15: Is it safe to look directly into the optical port of an active SFP‑10G‑SR? A: No. Even though it is Class1 laser product, invisible 850nm infrared VCSEL beam may damage human retina under long‑time direct exposure. Never stare at powered‑on optical ports or open fiber ends on running D‑Link network hardware.
Packaging & Custom OEM Solutions
Every 10G SFP+ module comes individually sealed in standard anti-static (ESD-safe) packaging, pre-stocked and ready for immediate shipment. For bulk orders, we offer custom OEM packaging—including logo printing and private labeling—tailored for network distributors, system integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



