Cisco SFP-10G-LR-S Compatible 10G SFP+ LR Optical Transceiver | 1310nm 10km SMF Bulk Supply | HYTOPTODEVICE
Product Overview
Looking for stable Cisco SFP-10G-LR-S compatible S-Class 10G SFP+ LR transceiver for long-distance single-mode fiber links? As a professional cisco sfp-10g-lr-s supply vendor, HYTOPTODEVICE provides drop-in replacement SFP+ modules matching SFP-10G-LR-S S-Class specification. Operating at 1310nm, this 10GBASE-LR optical module reaches 10km over OS2 single-mode fiber and does not support FCoE. Built-in DDM/DOM supports real-time optical parameter monitoring, pre-programmed S-Class EEPROM ensures seamless plug-and-play without Cisco port alarms. Every SFP-10G-LR-S module passes full optical testing before delivery. We offer bulk supply, sample testing, custom EEPROM and private label service for system integrators, network distributors and enterprise buyers searching for dependable cisco sfp-10g-lr-s supply.
Key Technical Specifications
| Cisco Compatible |
SFP-10G-LR-S |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP+ |
Max Data Rate |
10.7Gbps |
| Wavelength |
1310nm |
Max Distance |
10km |
| Connector |
Duplex LC |
Transmitter Type |
1310nm DFB |
| Cable Type |
OS2 SMF |
Receiver Type |
PIN |
| TX Power |
-6.5~-0.5dBm |
Receiver Sensitivity |
< -14.4dBm |
| Power Consumption |
≤1W |
Operation Temperature |
0 to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
-
Fiber Choice: OS1/OS2 single-mode fiber (9/125 µm) is correct. Standard duplex LC-LC connectors are standard. Do NOT use OM1/OM2/OM3/OM4 Multimode Fiber (MMF) cables; severe modal dispersion will prevent link establishment.
-
Connector Match: Clarify that UPC/PC is required for proper optical contact, while APC will result in an unusable link and excessive signal loss.
-
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
-
Link Tuning: If auto-negotiation fails with legacy SAN switches, manually lock the port speed to 10Gbps
-
Handling: Wear an ESD wrist strap during installation. Maintain a minimum fiber bend radius of 30 mm to prevent micro-bends and optical power loss.
-
Installation & Hot-Swap Rules
Supports MSA-compliant hot-swapping. Insert/remove gently without powering down the device. Keep dust caps on unused LC ports and avoid frequent re-plugging.
-
Operating Environment
Commercial grade: 0°C to 70°C in indoor environments. Keep away from extreme heat, moisture, and dust for long-term stability.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
● Cisco Nexus 2000 / 3000 / 4000 / 5000 / 6000 / 7000 / 9000 Series Switches
● Cisco Catalyst 3650 / 3850 / 4500-X / 9200 / 9300 / 9500 Series Switches
● Cisco ASR 1000 / 9000 Series Aggregation Services Routers
● Cisco ISR 4000 Series Integrated Services Routers
● Cisco Firepower 4100 / 9300 Series Firewalls
● Cisco UCS C-Series / B-Series Servers with SFP+ NIC
● Cisco NCS 4200 Series Network Convergence Systems
Minimum supported firmware: Cisco IOS / NX-OS stable release
2. Multi-Brand Cross Compatibility
This SFP-10G-LR-S compatible transceiver also works on Arista, Juniper, H3C, Dell and other mainstream SFP+ ports for mixed-brand network deployment when you source from our reliable cisco sfp-10g-lr-s supply.
3. Free Value-Added Services
● Custom S-Class EEPROM coding for multi-brand network device compatibility
● Sample validation before bulk orders for Cisco long-haul fiber projects
● Private label customization and network deployment guidance
● Strict batch consistency and optical performance testing
● Free EEPROM rewriting service
● 24/7 online technical support for 10GBASE-LR S-Class SFP modules
Main Application Scenarios
● 10G long-distance fiber uplink for Cisco Nexus and Catalyst switches
● Inter-building campus fiber connection and metropolitan backbone interconnection
● Enterprise backbone 10G single-mode fiber networking
● Data center remote disaster recovery and cross-site SAN links
● Bulk supply of Cisco S-Class SFP-10G-LR-S transceiver for global buyers via our cisco sfp-10g-lr-s supply
Connectivity Solutions(Applications)
1.10GbE Switch-to-Switch Connectivity

2.10GbE Switch to Media Converter Connectivity
3.10GbE Structured Cabling Interconnect

4.10GbE Switch-to-NIC Interconnection

5.10G Switch-to-4x10G Switch Interconnection

The Core Feature
1. 10G High-Speed Connectivity for Data Centers
Featuring 1W low power consumption, high density, and support for up to 10km transmission over single-mode fiber, this 10G SFP+ LR transceiver offers an efficient, reliable solution for upgrading your network infrastructure.
2.Seamless Compatibility & Reliability
Every unit undergoes rigorous compatibility testing across our lab's
150+ brand host devices to ensure seamless, flawless operation. Check device compatibility using our online tool, or request a switch-specific
Compatibility Video.
FAQ
Q1: What key distinctions exist between Cisco SFP-10G-LR and SFP-10G-LR-S transceiver?
A: The core gap lies in supported network protocols and operational adaptability.The standard SFP-10G-LR supports Ethernet, OTN, and WAN Phy protocols, and comes with a wider temperature variance. The S-Class SFP-10G-LR-S is an economical variant tailored exclusively for Ethernet only and is designed strictly for standard enterprise environments. Their distance (10km) ,wavelength(1310nm)and speed (10G) are identical. Bulk and long-term supply available for these two compatible modules from HYTOPTODEVICE.
Q2: Can I connect an SFP‑10G‑LR‑S to an SFP28 (25G) port?A: YES. SFP28 ports provide backward compatibility for SFP+ modules per MSA specification; this SFP+ 10G LR-S will negotiate and lock to 10.3125Gbps speed on 25G SFP28 host port. Verify your switch/NIC firmware enables SFP+ down‑speed mode; most modern Cisco NX-OS/IOS platforms support this function out‑of‑box for mixed‑rate long-distance uplink deployment with our Cisco compatible SFP-10G-LR-S S-Class optic.
Q3: Why does my switch show "Unsupported Transceiver" upon insertion?A: This alarm indicates host device rejects module EEPROM profile. Cisco IOS/NX-OS switches perform strict S-Class vendor‑specific EEPROM validation; generic MSA firmware will trigger alert even if optical hardware works normally. Use our pre‑flashed Cisco‑SFP‑10G‑LR‑S customized S-Class EEPROM version for zero‑alarm operation; avoid permanent CLI alarm‑masking on production backbone fabrics and upgrade switch firmware to latest stable release for your order from our cisco sfp-10g-lr-s supply.
Q4: Can I link an SFP‑10G‑LR‑S to a 10GBASE‑T (copper RJ45) port?A: NO. Direct interconnection is not feasible. SFP‑10G‑LR‑S is optical single-mode 1310nm S-Class transceiver while 10GBASE‑T is electrical copper signal; signal types are fundamentally different with no native conversion. Deploy a media converter or SFP‑10G‑T copper module to bridge optical LR-S link and RJ45 copper port for cross‑media interconnection scenarios using our Cisco 10G LR-S optics.
Q5: Will this module work in Network Interface Cards (NICs) like Intel or Broadcom?A: YES. This SFP+ 10G LR-S follows SFP+ MSA hardware specification and works with most SFP+‑based Intel X710, X520 and Broadcom NetXtreme series NICs. Some NIC firmware locks to original branded optics; select our generic MSA firmware variant for third‑party NIC hardware and confirm NIC firmware version before bulk server cluster deployment for Cisco fabrics with our cisco sfp-10g-lr-s supply modules.
Q6: What is the maximum transmission distance for SFP‑10G‑LR‑S?A: Maximum distance depends on single-mode fiber grade. It reaches 10km over OS2 SMF at 1310nm wavelength under 10.3125Gbps 10GBASE‑LR S-Class standard. Always use OS2 single-mode fiber within rated distance to maintain BER ≤1×10⁻¹²; exceeding reach will raise bit errors and trigger intermittent link flapping in Cisco long-haul backbone environments with our Cisco SFP-10G-LR-S S-Class replacement transceiver.
Q7: What is the optical power budget for SFP-10G-LR?
A: HYTOPTODEVICE Cisco SFP-10G-LR-S 10G SFP+ LR transceiver has an optical power budget of approximately 8 to 14 dB. With transmit power of -6.5 to -0.5 dBm and receiver sensitivity of ≤ -14.4 dBm (typical), this budget comfortably covers a full 10km OS2 SMF link (approximately 4.5dB total loss) with ample margin for stable, error-free operation.
Q8: What is the maximum transmit optical power?
A: HYTOPTODEVICE Cisco SFP-10G-LR-S 10G SFP+ LR transceiver has a maximum transmit optical power of -0.5 dBm, with an operating range of -6.5 to -0.5 dBm, delivered by a high-quality 1310nm DFB laser calibrated per IEEE 802.3ae 10GBASE-LR standards.
Q9: How does temperature affect signal quality and span distance?
A: Temperature causes laser wavelength drift and output power variation. Commercial grade modules (0°C to 70°C) maintain full 10km reach with stable BER. For outdoor cabinets, factory floors or harsh environments requiring -40°C to 85°C operation, choose our industrial temperature grade Cisco SFP-10G-LR-S modules with enhanced thermal compensation and ruggedized components.
Q10: What is the BER (Bit Error Rate) standard for this module?
A: HYTOPTODEVICE Cisco SFP-10G-LR-S 10G SFP+ LR transceiver meets the IEEE 802.3ae 10GBASE-LR standard BER of 1×10⁻¹² (one bit error per trillion bits) over the full 10km OS2 SMF link distance. Every module undergoes rigorous BER testing and 72-hour burn-in, verified on real Cisco Catalyst and Nexus switch platforms.
Q11: Why does my link drop intermittently after running for a few hours?
A: Common causes: dirty fiber end-faces, poor port contact, laser thermal drift from low-quality modules, or excessive cable bend radius. HYTOPTODEVICE Cisco SFP-10G-LR-S modules undergo 72-hour burn-in to eliminate early failures. Resolve intermittent drops by cleaning LC connectors, verifying cable bend radius and ensuring adequate switch port ventilation.
Q12: Are cheap third-party SFP-10G-LR modules reliable long-term?
A: Not all. Cheap alternatives often use ungraded lasers and skip aging testing, leading to early failures after 6-12 months. HYTOPTODEVICE Cisco SFP-10G-LR-S modules use premium 1310nm DFB lasers, 72-hour burn-in, real-device testing and a 5-year warranty — over 70% below OEM Cisco pricing with enterprise-grade reliability for long-term deployment.
Q13: Do these modules support hot-swapping?
A: Yes. HYTOPTODEVICE Cisco SFP-10G-LR-S 10G SFP+ LR transceiver fully supports hot-swapping per SFF-8431 MSA standards. Safely insert or remove the module while the Cisco switch remains powered on and operational — no restart required, minimizing network downtime for high-availability enterprise environments.
Q14: Can I use a Commercial grade SFP-10G-LR in an outdoor enclosure?
A: Not recommended unless the enclosure has active temperature control maintaining 0°C to 70°C. Outdoor enclosures can reach -40°C to +85°C, causing wavelength drift, power degradation and premature failure in commercial grade modules. For outdoor deployments, choose our industrial temperature grade (-40°C to 85°C) Cisco SFP-10G-LR-S modules with ruggedized components and enhanced thermal design.
Q15: Is SFP-10G-LR RoHS compliant?
A: Yes. HYTOPTODEVICE Cisco SFP-10G-LR-S 10G SFP+ LR transceiver is fully RoHS compliant (EU Directive 2011/65/EU), free of lead, mercury, cadmium, hexavalent chromium, PBB and PBDE below permitted thresholds. Also CE and FCC certified, compliant with MSA SFF-8431/SFF-8472 and IEEE 802.3ae standards for global enterprise deployment.
Packaging & Custom OEM Solutions
Our 10G SFP+ LR module comes sealed in standard anti-static (ESD-safe) packaging, pre-stocked and ready for immediate shipment. For bulk orders, we offer custom OEM packaging—including logo printing and private labeling—tailored for network distributors, system integrators, and enterprise deployments.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- 100% MSA-compliant modules with Cisco, Huawei,Dell,Juniper, and Arista compatibility
- ISO 9001:2015 certified manufacturing facility in Shenzhen
- Average lead time of 3–5 business days with DHL/FedEx express options
- Dedicated pre-sales engineering support for custom configurations
- Actual hardware,actual switches,actual results.we publish compatibility test video,eliminate compatibility anxiety. you can watch before you buy.
- We can provide inspection and shipping videos to make you feel as if you are right here with the product.
- Private Label support - EEPROM / firmware customization suppor
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

Others


