Juniper Networks SFP-1GE-EX-40 Compatible 1000BASE-EX Transceiver Module | SFP 1310nm 40km SMF Bulk Wholesale | HYTOPTODEVICE
Product Overview
HYTOPTODEVICE 1000BASE-EX transceiver module delivers full pin-to-pin compatibility with Juniper Networks SFP-1GE-EX-40. Custom pre-flashed EEPROM firmware resolves common industry pain points, including third-party transceiver module unrecognized failures, system error alarms and intermittent link drops on Juniper devices.
This 1310nm 1.25Gbps single-mode transceiver module supports steady 40km long-distance transmission, perfectly fitting enterprise cross-building interconnection and long-range WAN uplink scenarios.
Every transceiver module undergoes real Juniper device verification and high-temperature aging testing, ensuring consistent stable performance for large-scale bulk deployment and project procurement.
Key Technical Specifications
| Juniper Networks Compatible |
SFP-1GE-EX-40 |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP |
Max Data Rate |
1.25Gbps |
| Wavelength |
1310nm |
Max Distance |
40km |
| Connector |
Duplex LC |
Transmitter Type |
1310nm DFB |
| Cable Type |
SMF |
Receiver Type |
PIN |
| TX Power |
-5.0~0dBm |
Receiver Sensitivity |
< -23.0dBm |
| Typical Power Consumption |
≤1W |
Receiver Overload |
-1dBm |
| Bit Error Ratio (BER) |
1E-12 |
DDM/DOM |
Support |
| Protocols |
SFF-8472 MSA Compliant, IEEE 802.3ah-2004 |
Operation Temperature |
0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
-
Fiber Choice: Use Single-Mode Fiber (SMF) only. Do NOT use MMF
-
Connector Match: UPC/PC polish only. Do NOT use APC.
-
Cleanliness & Dust: Keep dust caps on all unused ports and connectors at all times. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
-
Optical Attenuator Required for Short Links: For testing or short-distance connections (<10 km), connect a 5dB–10dB optical attenuator to the RX port to prevent damaging the receiver.
-
Installation & Hot-Swap Rules:MSA hot-swappable. Insert/remove gently without powering down.
-
High Loss/Packet Drops: Check fiber bend radius (>30 mm); inspect optical power levels; clean optical connectors
-
No Link: Swap TX/RX fiber connections; clean fiber end-faces; verify port settings.
Links to the Datasheet, User Guide and Compatibility Guides are available on the product page.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
This compatible transceiver module adapts to mainstream Juniper switch, router and firewall hardware, fully compatible with official Junos firmware, maintaining zero-error operation after system upgrades.
-
Juniper EX Series Enterprise Switches: EX2300, EX3400, EX4100, EX4600, EX9200
-
Juniper QFX Series Data Center Switches: QFX5100, QFX5110, QFX5200
-
Full Junos firmware adaptation, plug-and-play without manual command configuration
2. Multi-Brand Cross Compatibility
Compliant with SFP MSA standards, this transceiver module supports multi-brand cross-device interoperability. It solves single-brand limits and meets diverse optical transceiver procurement needs.
3. Free Value-Added Services
We provide full value-added services for optical transceiver bulk purchase: free sample test, custom firmware, OEM service, low MOQ wholesale and 5-year warranty to avoid project after-sales risks.
Main Application Scenarios
-
Long-Distance Uplink: 40km optical module for cross-building campus and remote enterprise uplink interconnection
-
Module Batch Replacement: Cost-effective alternative for aging Arista SFP-1G-EX-40 optical module renewal
-
Enterprise WAN Expansion: Stable long-reach optical module for branch office network interconnection
-
Data Center Upgrade: Bulk optical module procurement for long-distance fiber link renovation
Connectivity Solutions(Applications)
1.1GbE Switch-to-Switch Connectivity

2.1GbE Switch to Media Converter Connectivity
The Core Feature
1. High-Efficiency & Low-Power 1G Data Center Interconnect
Low-power optical transceiver delivers stable 1.25Gbps transmission and 40km SMF long-reach connection. It solves high power consumption and unstable bandwidth pain points, ideal for data center bulk optical transceiver procurement.
2.Host-Tested for Proven Interoperability
All optical transceivers pass real Juniper device testing. Pre-flashed EEPROM ensures zero-alarm recognition, fixing third-party module incompatibility and link flapping for safe bulk purchase
.Specific Compatibility Video available upon request.
3.100% Factory Tested for Reliability
Every optical transceiver undergoes aging, calibration and stability tests. 0℃-70℃ wide temperature tolerance and DDM monitoring reduce network failure risks for large-scale procurement
. Take a virtual tour of our Test Center to see our Quality Assurance process in action.

FAQ
Q1: Will generic third-party transceiver modules work properly on official Juniper devices?
A: Yes. HYTOPTODEVICE Juniper SFP-1GE-EX-40 compatible transceiver module adopts dedicated vendor firmware programming, achieving full device recognition and zero-alarm stable operation on all matched Juniper hardware.
Q2: Can a 1G long-range EX transceiver module run on 10G SFP+ interface ports?
A: Yes. HYTOPTODEVICE’s Juniper-compatible SFP-1GE-EX-40 transceiver module works normally when the dual-speed 10G SFP+ host port is manually configured to 1Gbps operating mode.
Q3: Do Juniper replacement transceiver modules comply with global industry specifications?
A: Yes. HYTOPTODEVICE SFP-1GE-EX-40 transceiver module strictly conforms to IEEE 802.3z 1000BASE-EX and SFP MSA standards with universal cross-device interoperability.
Q4: Is it possible to deploy this 40km transceiver module on multimode fiber lines?
A: Yes. HYTOPTODEVICE 40km SFP-1GE-EX-40 transceiver module supports up to 550m multimode fiber transmission with a professional Mode Conditioning Patch cable to prevent DMD signal failure.
Q5: Can 1310nm long-range EX and 850nm short-range SX transceiver modules interconnect mutually?
A: No. To ensure stable links, the wavelength and fiber type of HYTOPTODEVICE SFP-1GE-EX-40 transceiver module must match the peer transceiver module end-to-end, otherwise complete link disconnection will occur.
Q6: Does this Juniper-compatible transceiver module support real-time DDM operational monitoring?
A: Yes. HYTOPTODEVICE SFP-1GE-EX-40 transceiver module features full DDM/DOM monitoring, supporting real-time detection of temperature, voltage, laser current and optical power for convenient daily maintenance.
Q7: What are the standard optical transmit power parameters of this 1000BASE-EX transceiver module?
A: This Juniper SFP-1GE-EX-40 compatible transceiver module delivers stable -5dBm ~ 0dBm TX power for reliable 40km long-distance fiber transmission.
Q8: How to troubleshoot weak signal and low receiving power faults on long-distance transceiver module links?
A: Clean fiber connectors thoroughly and check for fiber bending or excessive attenuation. The transceiver module’s ≤-23dBm high sensitivity ensures stable weak signal reception.
Q9: Are SC-LC fiber jumper cords compatible with Juniper SFP-1GE-EX-40 transceiver modules?
A: Yes. The transceiver module supports SC-LC jumpers, compatible with standard OS1/OS2 single-mode fiber and conventional LC interfaces.
Q10: Why are green APC fiber connectors incompatible with standard gigabit transceiver modules?
A: APC connectors are not applicable. Only blue UPC/PC connectors are supported to avoid high insertion loss and unstable transceiver module link signals.
Q11: What key factors cause intermittent link drops and unstable transceiver module connections?
A: Fiber contamination, excessive bending radius or abnormal optical power input will trigger transceiver module signal flapping and link instability.
Q12: What working temperature range can this commercial-grade transceiver module adapt to?
A: This transceiver module operates stably within 0℃ to 70℃, adapting to conventional enterprise equipment room operating environments.
Q13: Why is regular fiber cleaning critical for 1310nm single-mode transceiver module links?
A: Single-mode fiber cores are tiny and dust-sensitive, which easily interferes with transceiver module signal reception and undermines long-link transmission stability.
Q14: Do bulk Juniper replacement transceiver modules meet international certification standards?
A: Yes. All HYTOPTODEVICE transceiver modules comply with RoHS, CE, FCC and REACH standards for safe large-scale enterprise network deployment.
Q15: Will low-temperature environments affect transceiver module transmission performance?
A: Yes. Long-term operation below 0℃ may cause laser power offset and weaken the transceiver module’s overall transmission stability.
Packaging Options & Custom‑Packaging Solutions
Every transceiver module gets reliable ESD‑safe packaging out of the box. Standard packing is ready for immediate shipment, while custom‑printed packaging with your logo is available for bulk orders.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- 100% MSA-compliant modules with Cisco, Huawei,Dell,Juniper, and Arista compatibility
- ISO 9001:2015 certified manufacturing facility in Shenzhen
- Average lead time of 3–5 business days with DHL/FedEx express options
- Dedicated pre-sales engineering support for custom configurations
- Actual hardware,actual switches,actual results.we publish compatibility test video,eliminate compatibility anxiety. you can watch before you buy.
- We can provide inspection and shipping videos to make you feel as if you are right here with the product.
"We replaced 200 Cisco-branded SFPs with HYTOPTODEVICE equivalents across our spine layer — zero compatibility issues, 40% cost reduction."— Network Architect, Tier-2 ISP, Germany
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final inspection, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration
