Arista Networks SFP-1G-EX-40 Compatible 1000BASE-EX Optical Module | SFP 1310nm 40km SMF Bulk Wholesale | HYTOPTODEVICE
Product Overview
HYTOPTODEVICE 1000BASE-EX optical module features full pin-to-pin compatibility with Arista Networks SFP-1G-EX-40. Pre-flashed professional EEPROM firmware completely fixes common pain points including third-party optical module unrecognized failure, system alarm and intermittent link flapping.
This 1310nm 1.25Gbps single-mode optical module delivers stable 40km long-distance transmission, perfectly matching enterprise long-range cross-building and WAN interconnection scenarios.
Every optical module passes real Arista device testing and high-temperature aging calibration, ensuring consistent stable performance for large-scale bulk deployment.
Key Technical Specifications
| Arista Networks Compatible |
SFP-1G-EX-40 |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP |
Max Data Rate |
1.25Gbps |
| Wavelength |
1310nm |
Max Distance |
40km |
| Connector |
Duplex LC |
Transmitter Type |
1310nm DFB |
| Cable Type |
SMF |
Receiver Type |
PIN |
| TX Power |
-5.0~0dBm |
Receiver Sensitivity |
< -23.0dBm |
| Typical Power Consumption |
≤1W |
Receiver Overload |
-1dBm |
| Bit Error Ratio (BER) |
1E-12 |
DDM/DOM |
Support |
| Protocols |
SFF-8472 MSA Compliant, IEEE 802.3ah-2004 |
Operation Temperature |
0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
-
Fiber Choice: Use Single-Mode Fiber (SMF) only. Do NOT use MMF
-
Connector Match: UPC/PC polish only. Do NOT use APC.
-
Cleanliness & Dust: Keep dust caps on all unused ports and connectors at all times. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
-
Optical Attenuator Required for Short Links: For testing or short-distance connections (<10 km), connect a 5dB–10dB optical attenuator to the RX port to prevent damaging the receiver.
-
Installation & Hot-Swap Rules:MSA hot-swappable. Insert/remove gently without powering down.
-
High Loss/Packet Drops: Check fiber bend radius (>30 mm); inspect optical power levels; clean optical connectors
-
No Link: Swap TX/RX fiber connections; clean fiber end-faces; verify port settings.
Links to the Datasheet, User Guide and Compatibility Guides are available on the product page.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
This compatible optical module fits mainstream Arista switch series and official firmware versions, maintaining zero-error operation even after system upgrades without optical module recognition failure.
-
Arista 7000 / 7100 / 7200 Series Gigabit Switches
-
Arista EOS full firmware version adaptation
-
No manual command required, plug-and-play zero-alarm access
2. Multi-Brand Cross Compatibility
Compliant with SFP MSA standards, this optical module supports multi-brand cross-device interoperability. It solves single-brand limits and meets diverse optical transceiver procurement needs.
3. Free Value-Added Services
We provide full value-added services for optical transceiver bulk purchase: free sample test, custom firmware, OEM service, low MOQ wholesale and 5-year warranty to avoid project after-sales risks.
Main Application Scenarios
-
Long-Distance Uplink: 40km optical module for cross-building campus and remote enterprise uplink interconnection
-
Module Batch Replacement: Cost-effective alternative for aging Arista SFP-1G-EX-40 optical module renewal
-
Enterprise WAN Expansion: Stable long-reach optical module for branch office network interconnection
-
Data Center Upgrade: Bulk optical module procurement for long-distance fiber link renovation
Connectivity Solutions(Applications)
1.1GbE Switch-to-Switch Connectivity

2.1GbE Switch to Media Converter Connectivity
The Core Feature
1. High-Efficiency & Low-Power 1G Data Center Interconnect
Low-power optical transceiver delivers stable 1.25Gbps transmission and 40km SMF long-reach connection. It solves high power consumption and unstable bandwidth pain points, ideal for data center bulk optical transceiver procurement.
2.Host-Tested for Proven Interoperability
All optical modules pass real Arista device testing. Pre-flashed EEPROM ensures zero-alarm recognition, fixing third-party module incompatibility and link flapping for safe bulk purchase
.Specific Compatibility Video available upon request.
3.100% Factory Tested for Reliability
Every optical module undergoes aging, calibration and stability tests. 0℃-70℃ wide temperature tolerance and DDM monitoring reduce network failure risks for large-scale procurement
. Take a virtual tour of our Test Center to see our Quality Assurance process in action.

FAQ
Q1: Will this third-party optical module work normally on Arista switches without errors?
A: Yes. This HYTOPTODEVICE SFP-1G-EX-40 optical module adopts dedicated EEPROM programming, realizing full recognition and zero-alarm stable operation on Arista devices.
Q2: Is it feasible to install a 1G EX optical module into a 10G SFP+ port?
A: Yes. This Arista-compatible optical module works normally when the host dual-speed 10G SFP+ port is manually configured to 1G operating mode.
Q3: Are Arista SFP-1G-EX-40 replacement optical modules compliant with global standards?
A: Yes. The optical module fully conforms to IEEE 802.3z 1000BASE-EX and SFP MSA standards with universal interoperability.
Q4: Can this 40km long-range optical module operate over multimode fiber lines?
A: Yes. The optical module supports up to 550m multimode fiber transmission with a Mode Conditioning Patch cable to avoid DMD signal failure.
Q5: Is direct interconnection between 1310nm EX and 850nm SX optical modules supported?
A: No. Wavelength and fiber type of optical modules must match end-to-end, otherwise complete link failure will occur.
Q6: Does this Arista-compatible optical module support intelligent DDM link diagnosis?
A: Yes. The optical module supports full DDM/DOM monitoring to check temperature, voltage, laser current and optical power for easy maintenance.
Q7: What optical transmit power specifications define this 1000BASE-EX optical module?
A: This Arista-compatible optical module features stable -5dBm ~ 0dBm TX power for reliable 40km long-distance transmission.
Q8: How to resolve weak signal and low RX power issues on long-distance optical module links?
A: Clean fiber connectors and check fiber bending and attenuation. The optical module’s ≤-23dBm high sensitivity ensures stable weak signal reception.
Q9: Can SC to LC fiber patch cords pair with SFP-1G-EX-40 optical modules?
A: Yes. The optical module supports SC-LC jumpers, matched with standard OS1/OS2 single-mode fiber and LC interfaces.
Q10: Why are green APC fiber connectors incompatible with standard gigabit optical modules?
A: No. Only blue UPC/PC connectors are applicable. APC connectors cause high insertion loss and unstable optical module links.
Q11: What are the main triggers for unstable links and intermittent drops on EX optical module connections?
A: Fiber contamination, excessive bending or abnormal optical power input will trigger optical module signal flapping and link instability.
Q12: What temperature range can this commercial-grade optical module stably operate within?
A: This optical module works stably at 0℃ to 70℃, adapting to standard enterprise equipment room environments.
Q13: Why is professional fiber cleaning essential for 1310nm single-mode optical module links?
A: Single-mode fiber cores are tiny and sensitive to dust, which easily affects optical module signal reception and long-link stability.
Q14: Do bulk Arista replacement optical modules meet international safety and environmental certifications?
A: Yes. All optical modules comply with RoHS, CE, FCC and REACH standards for safe enterprise large-scale deployment.
Q15: Can freezing ambient temperatures impair optical module transmission performance?
A: Yes. Working below 0℃ may cause laser power shift and affect the optical module’s transmission stability.
Packaging Options & Custom‑Packaging Solutions
Every transceiver module gets reliable ESD‑safe packaging out of the box. Standard packing is ready for immediate shipment, while custom‑printed packaging with your logo is available for bulk orders.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- 100% MSA-compliant modules with Cisco, Huawei,Dell,Juniper, and Arista compatibility
- ISO 9001:2015 certified manufacturing facility in Shenzhen
- Average lead time of 3–5 business days with DHL/FedEx express options
- Dedicated pre-sales engineering support for custom configurations
- Actual hardware,actual switches,actual results.we publish compatibility test video,eliminate compatibility anxiety. you can watch before you buy.
- We can provide inspection and shipping videos to make you feel as if you are right here with the product.
"We replaced 200 Cisco-branded SFPs with HYTOPTODEVICE equivalents across our spine layer — zero compatibility issues, 40% cost reduction."— Network Architect, Tier-2 ISP, Germany
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final inspection, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

Others


