| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | GLC-BX120-U | SFP-G54-1BLD |
| 2 | Juniper | SFP-GE120KT14R15 | SFP-G34-10LD |
| 3 | Brocade | E1MG-1G-BXU-120 | SFP-G34-20LD |
| 4 | Dell | SFP-GE-BX120U-1490 | SFP-G35-20LD |
| 5 | Extreme | MGBIC-BX120-U | SFP-G34-40LD |
| 6 | H3C | SFP-GE-120-SM1490-A | SFP-G35-40LD |
| 7 | HPE H3C | SFP-1G-BXU-120 | SFP-G45-80LD |
| 8 | Netgear | SFP-GE-BX120-U |
| HPE H3C Compatible | SFP-1G-BXU-120 | Vendor Name | HYTOPTODEVICE |
| Form Factor | SFP | Max Data Rate | 1.25Gbps |
| Wavelength | TX1490nm/RX1550nm | Max Distance | 120km |
| Connector | Simplex LC | Transmitter Type | 1490nm DFB |
| Cable Type | SMF | Receiver Type | APD |
| TX Power | 1~5dBm | Receiver Sensitivity | < -32.0dBm |
| Protocols | SFF-8472 MSA Compliant, IEEE 802.3ah-2004 | Operation Temperature | 0 to 70°C (32 to 158°F) |
Complementary Pairing: BiDi transceivers must be deployed in matched pairs (e.g., TX1490/RX1550 with TX1550/RX1490). Mismatched wavelengths cannot establish a link.
Fiber Choice: Use Single-Mode Fiber (SMF) only. Do NOT use MMF.
Connector Match: Simplex LC (UPC/PC polish only). Do NOT use Duplex LC or APC.
Laser Safety: Class 1 Laser. Never look directly into optical ports or fiber end-faces.
ESD Safety: Wear an anti-static wrist strap before handling the transceiver.
Cleanliness & Dust: Keep dust caps installed on all unused ports. Clean fiber connectors with an optical cleaning pen before insertion; dust causes over 80% of link failures.
Optical Attenuator Required: For short-distance testing or links (<30 km), connect a 10dB–15dB attenuator to the RX port to prevent receiver damage.
Installation & Hot-Swap: MSA compliant. Insert and remove gently without powering down the device.
High Loss / Packet Drops: Ensure fiber bend radius exceeds 30 mm, inspect optical power levels, and clean connectors.
No Link: Verify complementary BIDI wavelength pairing requirement; clean Simplex LC end-faces; check port speed configuration.
1. Supported Hardware & Firmware








Q1: Can I fit this single fiber BiDi optic into a 10G SFP+ port on enterprise switches? A: Yes, this HYTOPTODEVICE BiDi module works on most SFP+ ports, but manually set port speed to 1Gbps. SFP+ ports support SFP backward compatibility, auto negotiation cannot downshift automatically from 10G to 1G.
Q2: Will this 120km single strand BiDi transceiver negotiate down to 100Mbps for legacy network hardware? A: This HYTOPTODEVICE BiDi module supports speed auto-adaptation, yet it is not recommended. Certain switch models may encounter compatibility mismatches and trigger unexpected link anomalies when running at lower speeds.
Q3: Do I need to upgrade switch firmware to recognize this HPE H3C compatible BiDi optic? A: Firmware updates are normally unnecessary for this HYTOPTODEVICE BiDi module. Our pre-calibrated EEPROM matches HPE H3C hardware; only very old switch firmware may trigger module unrecognized warnings.
Q4: Must I purchase matched wavelength pairs for this simplex BiDi SFP link deployment? A: Yes, BiDi communication requires paired modules with complementary wavelengths. This Tx1490/Rx1550 transceiver must pair with Tx1550/Rx1490 module on the opposite fiber end to build a working single-fiber connection.
Q5: Is it feasible to connect this BiDi SFP transceiver to duplex dual-fiber SFP via optical splitter? A: No, this setup cannot establish a stable network link. BiDi uses wavelength multiplexing over one fiber core while duplex SFP transmits and receives over separate fibers; wavelength mismatch blocks normal data transfer.
Q6: What receiver component is built inside this long range 120km BiDi optical module? A: This HYTOPTODEVICE 120km BiDi module adopts APD receiver. APD delivers much higher receiving sensitivity than PIN diodes, which is essential to achieve 120km long-reach single-mode fiber transmission.
Q7: When installing this 120km BiDi optic onsite, do I have to use inline optical attenuators? A: Attenuators are required for fiber links shorter than 30km. High launch power of 120km optics will overload APD receiver over short distances; use 10~15dB attenuator to protect the optical receiver.
Q8: Will aged G.652 single-mode fiber and fiber degradation reduce the maximum working distance of this BiDi transceiver? A: Yes, aged G.652 fiber with high loss or splice loss will shorten maximum working distance. Extra attenuation from old fiber reduces optical power budget and may break the 120km link margin.
Q9: How does chromatic dispersion affect 1.25G signal quality for 120km single fiber BiDi links? A: Chromatic dispersion has limited impact at 1.25G speed over 120km. Low gigabit rate is less sensitive to dispersion, but excessive dispersion will widen optical pulses and cause bit errors at the maximum 120km distance.
Q10: Why does my network switch display inaccurate RX power readings for BiDi SFP optics? A: BiDi wavelength filtering causes occasional DDM reading deviation. The reported RX power may be slightly inaccurate on some switch platforms, even if the actual fiber link remains stable.
Q11: Does this 120km long-distance BiDi optic run hotter than standard short reach 10km SFP modules? A: Yes, long-reach 120km BiDi modules generate slightly more heat. However, HYTOPTODEVICE modules feature optimized power consumption design, and thermal output is barely noticeable under normal operation, compared to low-power 10km short-range SFP transceivers.
Q12: Will continuous high operating temperature shorten the service life of the laser inside this 120km BiDi module? A: Yes, continuous high operating temperature accelerates laser aging. HYTOPTODEVICE modules pass temperature burn-in test, but prolonged over-temperature operation will reduce the service life of DFB laser and APD receiver.
Q13: Can the existing switch power supply handle full port population with multiple 120km BiDi SFP modules? A: Most modern enterprise switch power supplies support full populated ports. Each HYTOPTODEVICE BiDi module consumes ≤1W, you still need to calculate total power budget when fully filling all SFP slots.
Q14: Does HYTOPTODEVICE test each BiDi optic individually to verify 120km performance before shipment for bulk orders? A: Yes, every HYTOPTODEVICE BiDi module undergoes independent optical testing before shipment. We test optical power, sensitivity and link performance to guarantee 120km reach performance for bulk orders.
Q15: Are these wholesale BiDi transceivers compliant with RoHS and SFP MSA industry specifications? A: Yes, all HYTOPTODEVICE BiDi modules follow SFP MSA specifications and RoHS compliance. Standardized design ensures mechanical and electrical interoperability with most brand network hardware.
Packaging & Custom OEM Solutions
Individually sealed in ESD-safe packaging and ready to ship. We offer tailored OEM solutions—including custom logos and private labeling—to support high-volume distributors,wholesaler and system integrators.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



