A: Yes, complementary wavelength pairing is mandatory for all BiDi 100BASE-BX links. Our HYTOPTODEVICE iSFP-100-BX-U (Tx1310/Rx1550) module must pair with a reverse 100BASE-BX-D (Tx1550/Rx1310) transceiver at the opposite end to establish valid bidirectional fiber communication, which is the core working principle of single-fiber WDM technology.
Q2: What happens if I install TX1310/RX1550 modules on both ends of the fiber link?
A: Dual identical BX-U module deployment will result in complete link failure. Both ends transmit 1310nm signals and receive 1550nm signals simultaneously, causing wavelength mismatch and zero signal reception. Our professional BiDi module solution strictly supports one-to-one complementary pairing to avoid networking errors.
Q3: Will this 100BASE-BX SFP work in my Cisco, Juniper, Huawei, or HP switch?
A: Absolutely. Compatibility depends on the internal EEPROM coding. Ensure you specify your switch brand so the correct vendor-specific firmware is programmed before deployment. Our HYTOPTODEVICE Alcatel-Lucent compatible 100BASE-BX-U SFP features universal MSA compliance and customized vendor firmware, delivering plug-and-play, zero-alarm compatibility with Cisco, Juniper, Huawei, HP and all mainstream enterprise switch and router platforms, perfectly adapting to multi-brand mixed networking deployment.
Q4: Can I plug a 100BASE-BX SFP into a 1G SFP or 10G SFP+ port?
A: This 100Mbps BiDi SFP module supports adaptive operation on standard 100M/1G dual-rate SFP ports under specific device conditions. Most 10G SFP+ ports do not support 100Mbps speeds. Some 1G SFP ports support 100M if the switch ASIC allows forcing the port speed down to 100Mbps Full-Duplex. It cannot work on 10G SFP+ slots due to mismatched hardware protocols and rate specifications.
Q5: Can I use 100BASE-BX over Multimode Fiber (MMF)?
A: No. Our 20km 100BASE-BX-U transceiver is exclusively designed for G.652/G.657 single-mode fiber. Multimode fiber features large core diameter and high signal dispersion, which causes extreme optical attenuation, packet loss and link breakdown, unable to support long-distance BiDi transmission.
Q6: Can this 20km transceiver be used over short distances (e.g., 500 meters) without damaging the receiver?
A: Generally yes for 20km Fast Ethernet optics, as their output power is relatively low. However, you should check the receiver overload threshold in the datasheet to confirm. Our HYTOPTODEVICE 20km BiDi module features professional calibrated optical parameters (Tx: -14~-8dBm, Receiver Sensitivity: ≤-32dBm, Overload: -8dBm, Optical Budget: 18dB), supporting safe adaptive deployment from 500m to 20km without receiver damage or signal overload.
Q7: Does the 1550nm wavelength experience lower attenuation than 1310nm on the same fiber?
A: Yes. In standard single-mode fiber, the 1550nm window features inherently lower optical attenuation than the 1310nm wavelength. Our BiDi module utilizes this low-loss wavelength characteristic for downstream reception, ensuring more stable signal transmission for 20km long-range links.
Q8: Will attenuation differences between 1310nm and 1550nm cause link asymmetry?
A: Yes, the 1310nm direction will experience slightly higher path loss over 20km than the 1550nm direction, which must be factored into the link loss calculation. Our factory precision optical calibration compensates for this wavelength attenuation difference, eliminating obvious link asymmetry and ensuring stable, symmetric uplink and downlink performance within the 20km full transmission range.
Q9: Does this 100BASE-BX 20km SFP support DDM / DOM?
A: All our HYTOPTODEVICE iSFP-100-BX-U transceivers come with standard SFF-8472 compliant DDM/DOM real-time monitoring function. It supports real-time tracking of transmit/receive optical power, operating temperature, supply voltage and laser bias current for convenient network operation and fault diagnosis.
Q10: What is a normal Rx power reading in DDM for this module?
A: A healthy Rx power level typically ranges between -8 dBm and -28 dBm for stable error-free transmission. Readings below -32 dBm indicate a risk of link drops and insufficient signal strength, while readings higher than -8dBm will exceed the receiver overload threshold and cause signal distortion.
Q11: Is an Industrial Temperature (-40°C to +85°C) version available?
A: Yes. Beyond the standard 0°C~70°C commercial-grade module, HYTOPTODEVICE provides customized industrial-grade iSFP-100-BX-U transceivers with a -40°C~+85°C wide temperature range, suitable for outdoor cabinets, industrial workshops and harsh field networking environments.
Q12: What is the typical power consumption of a 100BASE-BX SFP?
A: Our 100BASE-BX-U BiDi SFP module features ultra-low power consumption below 1W. The energy-efficient chip design effectively reduces long-term operating power load for network devices, delivering eco-friendly and cost-saving stable operation for long-distance fiber links.