• Cisco GLC-BX80-DA-I compatible SFP BIDI TRANSCEIVER
  • industrial grade SFP BiDi module 80KM 1.25G SMF FROM HYTOPTODEVICE
  • HYTOPTODEVICE plug‑and‑play GLC‑BX80‑DA-I replacement BiDi SFP optical transceiver
  • 80KM BiDi SFP manufacturer
  • Cisco GLC-BX80-DA-I compatible SFP BIDI TRANSCEIVER
  • industrial grade SFP BiDi module 80KM 1.25G SMF FROM HYTOPTODEVICE
  • HYTOPTODEVICE plug‑and‑play GLC‑BX80‑DA-I replacement BiDi SFP optical transceiver
  • 80KM BiDi SFP manufacturer

Cisco GLC-BX80-DA-I Compatible Industrial SFP BIDI Transceiver 80km | 1000BASE-BX-D Tx1550Rx1490 Simplex LC Bulk Wholesale | HYTOPTODEVICE

HYTOPTODEVICE Cisco GLC-BX80-DA-I compatible industrial SFP BIDI transceiver, 1000BASE-BX-D Tx1550nm/Rx1490nm simplex LC, 80km OS1/OS2 single mode fiber. Wide industrial temperature range, pre-programmed IOS EEPROM. Factory bulk wholesale, custom EEPROM & private label for industrial network integrators.
NO. Brand  Compatible P/N Transceiver Type
1 Cisco GLC-BX80-DA SFP-G45-80LD
2 Cisco Cisco GLC-BX80-DA-I  SFP-G43-10LD
3 Brocade  E1MG-1G-BXD-80 SFP-G43-20LD
4 Dell  SFP-GE-BX80-1550 SFP-G53-10LD
5 Extreme MGBIC-BX80-D SFP-G53-20LD
6 H3C  SFP-GE-LH70-SM1550-BIDI SFP-G43-40LD
7 HPE H3C   SFP-1G-BXD-80  SFP-G53-40LD
8 Huawei  SFP-GE-ZBXD1 SFP-G54-1BLD
9 Juniper  SFP-GE80KT15R14
10 MikroTik  S-4554LC80D-1550
11 Netgear  SFP-GE-BX80-D
Description

Cisco GLC-BX80-DA-I Compatible Industrial SFP BIDI Transceiver 80km | 1000BASE-BX-D Tx1550Rx1490 Simplex LC Bulk Wholesale | HYTOPTODEVICE

Product Overview

HYTOPTODEVICE Cisco GLC-BX80-DA-I compatible industrial SFP BIDI transceiver follows IEEE 802.3z 1000BASE-BX-D standard. This wide-temperature single-fiber WDM optic runs 1.25Gbps up to 80km over OS1/OS2 SMF at Tx1550nm/Rx1490nm. Preloaded Cisco IOS optimized EEPROM ensures plug-and-play on Cisco IE industrial switches. As SFP BIDI transceiver manufacturer, we supply samples, bulk wholesale, custom EEPROM and private label for industrial system integrators.

Key Technical Specifications

Cisco Compatible  GLC-BX80-DA-I Vendor Name HYTOPTODEVICE
Form Factor SFP Max Data Rate 1.25Gbps
Wavelength TX1550nm/RX1490nm Max Distance 80km 
Connector Simplex LC Transmitter Type 1550nm DFB
Cable Type SMF Receiver Type PIN
TX Power 0~5dBm Receiver Sensitivity < -26.0dBm
Protocols SFF-8472 MSA Compliant, IEEE 802.3ah-2004 Operation Temperature -40 to 85°C (-40 to 185°F)

For detailed technical specifications, please refer to the Datasheet

Usage Guidelines & Operational Best Practices

  • Complementary Pairing: BiDi transceivers must be deployed in matched pairs (e.g., TX1490/RX1550 with TX1550/RX1490). Mismatched wavelengths cannot establish a link.

  • Fiber Choice: Use Single-Mode Fiber (SMF) only. Do NOT use MMF.

  • Connector Match: Simplex LC (UPC/PC polish only). Do NOT use Duplex LC or APC.

  • Laser Safety: Class 1 Laser. Never look directly into optical ports or fiber end-faces.

  • ESD Safety: Wear an anti-static wrist strap before handling the transceiver.

  • Cleanliness & Dust: Keep dust caps installed on all unused ports. Clean fiber connectors with an optical cleaning pen before insertion; dust causes over 80% of link failures.

  • Optical Attenuator Required: For short-distance testing or links (<20 km), connect a 10dB–15dB attenuator to the RX port to prevent receiver damage.

  • Installation & Hot-Swap: MSA compliant. Insert and remove gently without powering down the device.

  • High Loss / Packet Drops: Ensure fiber bend radius exceeds 30 mm, inspect optical power levels, and clean connectors.

  • No Link: Verify complementary BIDI wavelength pairing requirement; clean Simplex LC end-faces; check port speed configuration.

For detailed operation instructions, please refer to the User Guide.

Full Compatibility List and Supported Devices


1. Supported Hardware & Firmware

This Cisco GLC‑BX80‑DA‑I compatible industrial‑grade transceiver uses Cisco‑optimized industrial‑profile firmware to eliminate unrecognized transceiver alarms. It runs smoothly on qualified mainstream Cisco IOS / IOS‑XE firmware for both rugged industrial and commercial network hardware.
● Cisco Industrial Rugged Switches & Routers (‑40℃~+85℃ compatible platforms)
 ○ IE3300 Rugged Series
 ○ IE3400 Heavy‑Duty Series
 ○ IE3500 Heavy‑Duty Series
 ○ IE4000 Industrial Ethernet Series
 ○ IR1101 Rugged Integrated Services Router
 ○ IR829 Industrial Integrated Services Router
● Cisco Commercial Catalyst Switches (0‑70℃ indoor office deployment only)
 ○ Catalyst 2960 Series: 2960, 2960‑S, 2960‑X, 2960‑XR, 2960‑C
 ○ Catalyst 3560 / 3750 Series: 3560‑C, 3560‑X, 3750‑X
 ○ Catalyst 3850 Series: WS‑C3850‑24T, WS‑C3850‑48T
 ○ Catalyst 9000 Series: 9200, 9200L, 9300, 9400, 9500
● Cisco Commercial Data Center & Office Routers (indoor ambient environment only)
 ○ ISR 4000 Series: 4321, 4331, 4351, 4431, 4451
 ○ ASR 1000 Series: ASR 1001‑X, ASR 1002‑X

2. Multi-Brand Cross Compatibility

This transceiver complies with MSA standards, interoperable with Huawei, H3C, Juniper, Arista, Brocade, Dell network hardware. Custom EEPROM programming available for multi‑vendor mixed industrial‑site networking.

3. Free Value-Added Services

We provide professional customization for bulk Bidi sfp transceiver module orders, including firmware adaptation and custom labeling, meeting personalized procurement demands for compatible optical modules.

Primary Application Scenarios

● Field‑site single‑strand fiber point‑to‑point industrial network links
● Outdoor cabinet and remote‑site long‑distance gigabit connectivity
● ISP remote‑node fiber access and FTTH network upgrade
● Harsh‑environment security surveillance long‑distance fiber backhaul
● Dark‑fiber point‑to‑point links under fiber‑core shortage for industrial project


Connectivity Solutions (Applications)

1.1GbE Switch-to-Switch Connectivity
HYTOPTODEVICE BiDi SFP transceiver for Cisco single‑fiber point‑to‑point enterprise deployment
2.1GbE Switch to Media Converter Connectivity
HYTOPTODEVICE 80km BiDi SFP for campus long‑haul gigabit inter‑building links
3.1G Structured Cabling
HYTOPTODEVICE single strand SFP for ISP FTTH and remote branch backhaul


Core Product Features

1. Single-Fiber WDM Optimization

Cut cabling costs in half. Enables full bidirectional traffic over a single fiber strand using WDM technology—maximizing existing network infrastructure without extra wiring.
hytoptodevice bidi sfp transceiver 1.25g LC connector SMF 80km

2.Double Bandwidth, Zero New Fiber

Instant network expansion. Transmit bi-directionally on a single strand to instantly double link capacity—delivering cost-effective, high-efficiency bandwidth for Cisco enterprise and FTTx upgrades.

80km LC TX1490/RX1550 BiDi SFP Module double network bandwidth bulk wholesale chart for Cisco network upgrade

3. Low-Power 1G Single-Fiber Connectivity

Cut energy and cabling costs simultaneously. Enables high-efficiency Gigabit Ethernet links over a single fiber strand with optimized, low-power operation.
gigabit single fiber module with low power

4. Plug-and-Play Guaranteed Compatibility

Eliminate link flapping and third-party alarms. Every module is host-tested on real devices with pre-flashed EEPROM for seamless, vendor-safe bulk deployments. Specific Compatibility Video available upon request.

HYTOPTODEVICE GLC‑BX80‑UA compatible SFP validated on Cisco IOS platforms

5. 100% Tested, Zero-Defect Guaranteed
Maximum network uptime, zero surprises. Every module undergoes rigorous physical testing in our Test Center before shipping to deliver rock-solid reliability out of the box.

HYTOPTODEVICE BiDi SFP transceiver full aging test for stable 80km single‑fiber operation


Frequently Asked Questions 

Q1: Does this industrial 80km SFP BIDI transceiver follow SFP MSA mechanical and electrical standards? A1: Yes, this industrial SFP BIDI transceiver fully complies with SFP MSA specs. Any hardware with standard 1.25G SFP slots and single-fiber support can achieve basic interoperability. Custom EEPROM may still be required to remove Cisco IOS vendor-specific alarm logs.

Q2: Is wavelength pairing mandatory to set up a working BiDi single fiber gigabit link? A2: Yes. BiDi communication requires matched opposite wavelength pairs. Pair this Tx1550/Rx1490 module with Tx1490/Rx1550 BiDi transceiver on the opposite end. Using same wavelength modules on both sides creates total link loss and LOS alarms.

Q3: Can I deploy this industrial long-range BiDi transceiver using multimode fiber cables? A3: No. This 80km transceiver is designed exclusively for single-mode fiber. Multimode fiber cannot satisfy dispersion and loss requirements for 80km 1000BASE-BX-D transmission, only use OS1 or OS2 single-mode fiber.

Q4: Can this 80km-rated industrial SFP BIDI transceiver be used on fiber spans shorter than 10km? A4: Yes, but you must install inline optical attenuator (10–15dB) to protect the sensitive PIN receiver. Excessive received optical power overloads receiver and causes unstable links or permanent hardware damage.

Q5: What fiber connector type is required for this industrial gigabit BiDi optical transceiver? A5: This SFP BIDI transceiver uses simplex LC/UPC connector. Duplex LC connectors are not compatible for single-strand BiDi operation. Use simplex-LC terminated OS1/OS2 single-mode patch cords for proper connection.

Q6: Will DDM DOM optical monitoring function properly across mixed brands of industrial switches and routers? A6: DDM/DOM follows SFF-8472 standard, supporting real-time Tx power, Rx power and temperature readings on most MSA-compliant hardware. Cisco IOS may limit or hide DDM readouts for third-party transceivers even if hardware monitoring works.

Q7: Can unclean fiber connector end faces trigger transceiver failure or intermittent industrial network link drops? A7: Yes. Dust, oil and scratches on fiber ends introduce insertion loss and signal reflection. It causes intermittent packet loss and link flapping; heavy contamination can damage internal optical parts. Always clean LC connectors before field installation.

Q8: Can this wide-temperature industrial SFP BIDI transceiver be applied to CPRI cellular tower radio interfaces? A8: This industrial grade (-40~85°C) SFP BIDI transceiver supports gigabit Ethernet only, it is not built for CPRI radio interfaces. It works for gigabit backhaul if your hardware supports 1000BASE-BX-D. Choose dedicated CPRI optics for tower CPRI links.

Q9: What compliance documents should buyers request when placing bulk wholesale orders of industrial BiDi transceivers? A9: This transceiver meets RoHS, SFP MSA and IEEE 802.3z gigabit Ethernet standard. When purchasing bulk from manufacturer, you can request optical test reports, thermal aging burn-in records and compliance certificates.

Q10: What MTBF value can buyers expect for this industrial SFP BIDI transceiver under rated wide temperature working conditions? A10: Lab tested typical MTBF exceeds 1,000,000 hours within -40~85°C industrial temperature range. MTBF is a statistical value and not a guaranteed service life; actual lifespan depends on cabinet cooling, fiber cleanliness and harsh site environment.

Q11: Is custom EEPROM programming available for older legacy Cisco IE industrial switches during bulk procurement? A11: Yes, custom EEPROM rewriting service is available for bulk orders. As a transceiver manufacturer, we can customize vendor profiles for legacy Cisco industrial hardware to clear unrecognized module alerts. Please provide exact Cisco model, IOS firmware version and OEM part number in pre-sales consultation.

Q12: What causes the “Unsupported Transceiver” warning on Cisco IE industrial switch SFP ports? A12: This alert appears when Cisco IOS rejects generic default EEPROM data. It is normally fixed by flashing Cisco-matched customized EEPROM profile. Verify device model and firmware; some older Cisco industrial hardware has hardware locks for third-party optics.

Q13: Can a standard optical power meter validate the transmit optical power of this industrial BiDi transceiver? A13: Yes, an optical power meter calibrated for 1550–1490nm wavelength band can measure transmit power. Receive power cannot be measured externally; read Rx power via DDM/DOM page on the connected Cisco network device.

Q14: What troubleshooting information should I submit to technical support when facing faulty industrial transceiver issues? A14: Prepare these details: transceiver part number, Cisco IE host device model & IOS firmware version, DDM screenshots (Tx/Rx power, temperature), fiber type & total link distance, paired BiDi module wavelength, symptoms (LOS, link flapping, alarm text) and field site environment description. This information speeds fault diagnosis greatly.


Packaging & Custom OEM Solutions

Individually sealed in ESD-safe packaging and ready to ship. We offer tailored OEM solutions—including custom logos and private labeling—to support high-volume distributors,wholesaler and system integrators.
HYTOPTODEVICE sfp-10g-sr optical transceiver module custom package

Why Network Engineers Choose HYTOPTODEVICE

HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.

  • 100% hardware-tested compatibility with Cisco, Huawei,Dell,Juniper, and Arista
  • ISO 9001:2015 certified manufacturing facility in Shenzhen
  • Full product range coverage:1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T
  • In-stock supply & fast global shipping, average lead time of 3–5 business days with DHL/FedEx express options
  • Dedicated pre-sales engineering support for custom configurations
  • Actual hardware,actual switches,actual results.we publish compatibility test video,eliminate compatibility anxiety. you can watch before you buy. 
  • We can provide inspection and shipping videos to make you feel as if you are right here with the product.
  • Private Label support - EEPROM / firmware customization support

“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia

Quality Certification & Compliance

 At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.

We adhere to rigorous standards for our SFP modules and network solutions:

  • ISO 9001: Certified quality management and production consistency.

  • CE & FCC: Fully compliant for seamless Global Market Access.

  • RoHS: Committed to environmental responsibility and hazardous material control.

  • Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.

Certified Quality. Global Standards. Guaranteed Performance.




Rigorous Industrial Product Testing

   

100% 3rd Party Compatible

Partial Test Demonstration

  • Cisco GLC-BX80-DA-I compatible SFP BIDI TRANSCEIVER
  • industrial grade SFP BiDi module 80KM 1.25G SMF FROM HYTOPTODEVICE
  • HYTOPTODEVICE plug‑and‑play GLC‑BX80‑DA-I replacement BiDi SFP optical transceiver
  • 80KM BiDi SFP manufacturer

Download