Juniper Networks JNP-QSFP-100G-SR4 Compatible 100GBASE-SR4 100G QSFP28 Optical Transceiver SR4 | HYTOPTODEVICE(100m, MMF, 850nm, MPO-12, DOM)
Product Overview
Our Juniper Networks JNP-QSFP-100G-SR4 Compatible transceiver is a high-precision drop-in replacement for short-reach data center interconnects. Designed for 103.125Gbps total bandwidth via four independent 25.78Gbps NRZ optical lanes, it delivers stable low-latency 100G transmission with 850nm over OM3 and OM4 multimode fiber: up to 70 meters on OM3 MMF and extended 100 meters on OM4 MMF.Compliant with QSFP28 MSA, SFF-8636, IEEE 802.3bm, and CAUI-4 standards,fully DDM/DOM real-time monitoring support,featuring high-speed and low-latency, the 100G QSFP28 optical transceiver SR4 is ideal for data centres, high-performance computing networks, enterprise core and distribution layer applications.
Key Technical Specifications
| Juniper Networks Compatible |
JNP-QSFP-100G-SR4 |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
QSFP28 |
Max Data Rate |
103.125Gbps (4x 25.78Gbps) |
| Wavelength |
850nm |
Max Distance |
100m on OM4 |
| Connector |
MTP/MPO-12(UPC) |
Transmitter Type |
850nm VCSEL |
| Cable Type |
MMF |
Receiver Type |
PIN |
| TX Power |
-8.4~+2.4dBm |
Receiver Sensitivity |
< -9.5dBm |
| Protocols |
100G Ethernet, MSA Compliant |
Power Consumption |
< 2.0W |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
-
Fiber Choice: Only works with OM3 / OM4 multi‑mode MPO‑12 trunk cable; single‑mode fiber cannot support 850nm SR4 transmission and will lead to link failure.
-
Distance Limit: Max 70m on OM3 MMF, max 100m on OM4 MMF; excessive splices, dirty end‑faces or sharp bends reduce actual working distance.
-
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
-
Installation Specification: Hot‑plug supported; keep MPO connector end‑faces clean, observe minimum fiber‑bend radius requirements.
- Port Configuration: Confirm host ports are set to 100G SR4 mode; do not mix SR4 with other 100G optical standards on the same link.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Network Hardware
1.Native Juniper Networks JunOS Compatibility
This HYTOPTODEVICE 100G QSFP28 Optical Transceiver SR4 delivers zero-alarm plug-and-play recognition on all mainstream Juniper JunOS leaf-spine switches and core routers, with complete DDM/DOM parameter reading accessible via JunOS CLI and web management portal. Fully compatible Juniper hardware series:
- QFX Data Center Leaf-Spine Switches: QFX5100, QFX5120, QFX5200, QFX5220, QFX10000 Series
- MX Universal Service Routers: MX10003, MX10008, MX204, MX240, MX480, MX960 Series
- PTX Packet Transport Core Routers: PTX1000, PTX10002, PTX10008, PTX3000 Series
2. Multi-Brand Cross Compatibility
Built on universal industry MSA standards, HYTOPTODEVICE 100G QSFP28 SR4 compatible transceivers provide excellent cross‑brand interoperability. They work seamlessly with Arista, Cisco, Juniper, H3C, Dell, NVIDIA/Mellanox hardware and other more, supporting multi‑vendor hybrid networking and flexible short‑reach 100G data‑center deployment.
3. Free Value-Added Services
-
Custom firmware for multi-device compatibility
-
Support sample testing before bulk orders for project pre-verification
-
Private-label customization and professional deployment guidanc
-
Strict batch consistency quality control
- Free custom EEPROM programming for special and legacy network environments
- Free EEPROM rewriting (Tools Included) with 24/7 Tech Support
Primary Application Scenarios
- Hyperscale Juniper QFX leaf-spine 100G multimode uplink expansion and fabric upgrade projects
- HPC high-performance computing low-latency server interconnection clusters
- Enterprise core layer 100G aggregation MPO trunk upgrade deployment
- Metro ISP central office 100G business broadband aggregation transport fabrics
- Global system integrator indoor turnkey multimode 100G bulk engineering deployment projects
Connectivity Solutions(Applications)
1. 100G Switch-to-Switch Interconnection

2.100G Switch-to-NIC Direct Connection

3.100G to 4×25G Breakout Link with Switch

4.100G to 4×25G Breakout Link with NIC

The Core Feature
1. Low Power, High- Density 100G Connectivity for Data Center
HYTOPTODEVICE QSFP28 100G SR4 transceiver delivers ultra-stable 100Gbps transmission with industry-leading low power consumption. Engineered for maximum reliability in high-density data center environments.

2.Host-Device Tested for Proven Interoperability
Every transceiver is rigorously tested for compatibility in the target switch environment, so you can deploy with confidence — no surprises, no downtime. Not sure it fits?
Compatibility Video available upon request.
3. 100% Individually Tested for Peak Performance
Every single unit is tested individually — no sampling, no shortcuts — to ensure optical compliance and continuous operational stability. Curious how we do it? Take a virtual tour of our
Test Center.

FAQ
Q1: Can HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 run without extra config on Cisco, Arista and Juniper switches?
A: Most mainstream enterprise switches lock third-party optics via vendor-specific EEPROM rules. Our HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 supports fully customizable EEPROM vendor coding. Simply tell us your exact switch model during order placement, and our engineering team will preload matched compatible firmware to deliver native zero-alarm operation out of the box.
Q2: Is it possible to install a HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 into legacy 40G QSFP+ switch ports?
A: This operation is not supported for stable network transmission. Though the HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 shares similar shell dimensions with 40G QSFP+ modules, their internal high-speed circuit architectures differ completely. 100G QSFP28 ports accept down-rate 40G optics, but 40G QSFP+ slots lack 4×25G signal processing to initialize 100G SR4 transceivers, leading to port unrecognition and link failure.
Q3: Does HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 offer direct auto-negotiation to 10G or 25G transmission speeds?
A: No. The HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 adopts native 4×25G NRZ hardware architecture and cannot auto-negotiate down to standalone 10G or 25G rates. It only supports lower-speed traffic when paired with MPO breakout cables and compatible switch OS breakout function enabled.
Q4: What fiber port connector interface comes equipped on HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4?
A: The HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 is factory fitted with a standard MPO-12 female connector, also interchangeably named MTP-12 for parallel multimode data center trunk cabling.
Q5: Do I need 8-fiber or 12-fiber MPO trunk cables to match HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4?
A: You must deploy full MPO-12 trunk cables for the HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4. Only 8 fibers are functional for transmission (4 Tx lanes + 4 Rx lanes), while the middle four fibers inside the 12-fiber assembly remain unused without impacting normal 100G performance.
Q6: What causes HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 to hit temperatures above 60°C and will high heat damage the module?
A: 60°C falls within the normal commercial operating temperature window for the HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4. If the internal module temperature exceeds 70°C continuously, it points to insufficient rack airflow or faulty switch fans, which accelerates laser aging and shortens the transceiver’s full service lifespan.
Q7: Why does HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 show normal Tx power reading but low Rx power or LOS loss of signal alarms?
A: Normal transmit power paired with low receive power or LOS alarms on the HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 means optical signals fail to reach the receiving end effectively. Check MPO trunk cables for sharp bends, physical cracks, or dust and oil contamination on the MPO-12 connector end-faces.
Q8: What triggers random intermittent packet loss and CRC error alerts on ports using HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4?
A: Intermittent packet drops and CRC errors with the HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 mostly stem from marginal optical power levels caused by dirty MPO connectors, or running fiber links at the absolute 100-meter OM4 limit without RS-FEC error correction activated on both switch ends.
Q9: Will deploying HYTOPTODEVICE third-party 100G QSFP28 Optical transceiver SR4 invalidate my brand switch hardware warranty?
A: Using HYTOPTODEVICE certified 100G QSFP28 Optical transceiver SR4 will not void your original switch warranty. Protected by the Magnuson-Moss Warranty Act in the US and most global regions, network hardware brands cannot legally void warranty coverage solely for using compliant third-party optics, unless the transceiver directly causes permanent physical port damage.
Q10: How can buyers confirm the internal VCSEL laser quality inside HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4?
A: All HYTOPTODEVICE 100G QSFP28 Optical transceiver SR4 utilize premium industrial VCSEL laser chips sourced from top-tier manufacturers including II-VI, Broadcom and Lumentum, which deliver consistent low-jitter performance and long-term stable reliability for data center parallel multimode links.
Packaging & Custom OEM Solutions
-
ESD Protection & Fast Shipping: Every module is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
-
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

