| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-100G-ZR4-S | QSFP28-100G-SR4 |
| 2 | Cisco | QSFP-100G-ZR4-S-I | QSFP28-100G-PSM4 |
| 3 | Arista | QSFP-100G-ZR4 | QSFP28-100G-IR4 |
| 4 | Ciena | XCVR-Q80V31 | QSFP28-100G-LR4 |
| 5 | Juniper Networks | QSFP-100G-ZR4 | QSFP28-100G-ER4L |
| 6 | H3C | QSFP-100G-ZR4-WDM1300 | QSFP28-100G-DR |
| 7 | Generic | 100GBASE-ZR4 | QSFP28-100G-FR |
| Cisco Compatible | QSFP-100G-ZR4-S | Vendor Name | HYTOPTODEVICE |
| Form Factor | QSFP28 | Max Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 1295.56nm, 1300.05nm 1304.58nm, 1309.14nm |
Max Distance | 80km |
| Connector | Duplex LC/UPC | Transmitter Type | EML LWDM |
| Cable Type | SMF | Receiver Type | SOA + PIN |
| Modulation (Electrical) | 4x 25G-NRZ | TX Power | 1~6.5dBm |
| Power Consumption | < 4.5W | Receiver Sensitivity | < -28dBm |
| Protocols | QSFP28 MSA, SFF-8636, IEEE 802.3bm, CAUI-4 | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Works only with OS2 single-mode fiber. Multimode fiber is not compatible with this 1310nm LAN WDM module.
Optical Attenuator Required for Short Links: For testing or short‑distance connections (<15km), connect a 15dB–20dB optical attenuator to the RX port to prevent damaging the receiver.(15KM<Distance<35km,connect 10‑15dB optical attenuator),ensuring the received power between -28~-7dBm.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Installation Specification: Hot-swap supported. Follow ESD anti-static procedures and keep LC connectors clean for stable links.
Operating Environment: 0°C–70°C commercial temperature range. Ensure cabinet ventilation to avoid optical power attenuation from overheating.
Full Compatibility List & Supported Network Hardware
1. Supported Hardware & Firmware
This module adopts Cisco‑specific EEPROM, supporting zero‑alarm plug‑and‑play with official firmware. All products are strictly tested, fully compatible with the below Cisco hardware models:
• Cisco Catalyst 9000 Series Switches: C9300, C9500
• Cisco Nexus Data Center Switches: N9K‑C9332C, N9K‑C9364C, N9K‑C9504
• Cisco ASR Routers: ASR 1000‑X, ASR 9000 Series
• Universal Compatibility: All Cisco devices with standard QSFP28 ports supporting 100GBASE‑ZR4 protocol







Q2: What performance differences exist between 100GBASE‑ZR4 and ER4 when sourcing compatible Cisco 100G optical modules for metro‑DCI tender projects? A: ZR4 supports extended 80km maximum reach versus ER4’s 40km reach with higher power consumption at 4.5W max. Tested under HYTOPTODEVICE lab conditions, ZR4 keeps bit error rate below 1E‑12 only with RS‑FEC activated and received power between ‑28 ~‑7dBm. Distributors can recommend this long‑reach variant for metro‑DCI deployments requiring 40‑80km fiber spans.
Q3: Can this Cisco compatible 100GBASE‑ZR4 optic operate over dual‑core OS2 single‑mode fiber for cross‑campus long‑haul backbone builds? A: Yes, this HYTOPTODEVICE QSFP28 ZR4 requires two OS2 single‑mode fiber cores for bidirectional 100G traffic. LAN‑WDM four‑channel wavelengths are multiplexed inside one transceiver housing. Procurement teams should confirm duplex fiber availability, RS‑FEC port capability and optical power budget during site survey before ordering bulk quantities of these compatible transceivers.
Q4: Is OM multimode fiber acceptable when deploying Cisco QSFP‑100G‑ZR4‑S equivalent transceivers for long‑distance inter‑building DCI links? A: Multimode fiber cannot satisfy this 80km transmission requirement. Even high‑grade OM4 multimode has excessive modal dispersion, limiting 100G reach to only 100‑150 meters. HYTOPTODEVICE recommends end‑users deploy OS2 single‑mode fiber exclusively, which wholesalers can bundle together with transceiver orders for complete project kits.
Q5: Why is the 1310nm LAN‑WDM band selected for Cisco 80km 100G metro‑DCI compatible transceivers? A: LAN‑WDM 1295‑1309nm window exhibits typical 0.22dB/km attenuation on OS2 fiber. HYTOPTODEVICE calibrates each laser channel to this wavelength grid, ensuring consistent optical budget for 80km runs. System integrators benefit from low signal loss without resorting to expensive C‑band DWDM components for enterprise metro‑DCI links.
Q6: How to select proper optical attenuator for different short‑haul fiber spans using Cisco compatible QSFP28 ZR4 100G transceivers? A: Attenuators are mandatory for links below 35 km to keep received power within valid‑28 ~‑7dBm working window. For testing or short‑distance connections (<15km), deploy 15‑20dB duplex LC optical attenuator on RX port; for links between 15‑35km, adopt 10‑15dB duplex LC attenuator. Improper attenuation will trigger receiver overload or insufficient sensitivity and cause link instability. HYTOPTODEVICE advises buyers strictly follow above power‑matching rules to protect receiver hardware.
Q7: How much chromatic dispersion margin is reserved on HYTOPTODEVICE Cisco‑compatible 100GBASE‑ZR4 modules for real‑world 80km fiber routes? A: Each unit is pre‑characterized for OS2 fiber chromatic dispersion up to maximum 80km distance under RS‑FEC enabled and received power ‑28 ~‑7dBm condition. Our factory burn‑in test simulates real‑world fiber dispersion conditions, keeping post‑FEC bit‑error‑rate well under 1E‑12. This provides safety margin for splice and connector losses frequently encountered in integrator‑managed leased‑fiber metro‑DCI projects.
Q8: What hardware damage risks arise from improper received optical power on drop‑in Cisco 100G QSFP28 ZR4 replacement parts? A: Excessive receive power above‑7dBm can permanently degrade the internal photodiode receiver; signal will drop out if incoming power goes below‑28dBm sensitivity threshold. Field statistics collected by HYTOPTODEVICE RMA data show roughly 60% of returned long‑reach 100G transceivers stem from wrong attenuation setting on short‑link operation. Distributors should pass complete power‑matching deployment guidance along to their end‑customer technical teams.
Q9: What ambient operating conditions apply to commercial‑grade Cisco QSFP‑100G‑ZR4‑S alternative transceivers from HYTOPTODEVICE? A: Standard commercial SKU reliably operates from 0℃ to +70℃ cabinet ambient. Every HYTOPTODEVICE unit passes 8‑hour high/low‑temperature cycling during production QA. Wholesalers with outdoor cabinet tenders may inquire about our industrial‑grade ‑40~+85℃ variant for non‑climate‑controlled field hardware deployments.
Q10: Do HYTOPTODEVICE Cisco‑compatible QSFP28 ZR4 transceivers adhere to global MSA and IEEE specifications for third‑party 100G switch optics? A: Yes, all electrical, mechanical and optical parameters follow IEEE and QSFP28 MSA SFF‑8665 standards. Full DDM/DOM monitoring registers follow MSA defined memory map. This compliance enables system integrators to mix‑and‑match alongside other MSA‑compliant optics inside multi‑vendor network fabrics, note that RS‑FEC function is host‑dependent and received power must stay within‑28 ~‑7dBm.
Q11: What compliance documentation is supplied when purchasing bulk quantities of Cisco‑compatible 100G QSFP28 ZR4 transceivers? A: Each bulk shipment includes CE, FCC, RoHS compliance certificates plus batch‑specific optical test reports including Tx power, receiver sensitivity and overload index. HYTOPTODEVICE exports complete document sets assisting customs clearance and enterprise‑carrier project audit requirements. Global resellers can request additional declaration forms to satisfy regional import regulatory constraints.
Q12: What warranty and advanced‑replacement terms apply for project‑scale bulk orders of HYTOPTODEVICE Cisco replacement 100G transceivers? A: Standard factory warranty covers early‑life hardware defects with fast advanced‑replacement logistics. High‑volume system‑integrator metro‑DCI projects qualify for priority stock reservation. Distributors with recurring quarterly procurement volumes can open dedicated support tickets to accelerate RMA processing for their end‑client sites.
Q13: What preventive maintenance work should operators perform on deployed 80km 100GBASE‑ZR4 Cisco‑compatible transceivers? A: Visual port cleaning and insertion‑loss spot‑check every 6‑12 months is recommended. Contaminated LC end‑faces account for many slow‑degrading intermittent faults. HYTOPTODEVICE suggests network operators integrate DDM power‑threshold alerts to monitor real‑time RX power within‑28 ~‑7dBm, together with periodic RS‑FEC error‑counter reading as part of routine O&M workflows for metro‑DCI backbone infrastructure.
Q14: Can HYTOPTODEVICE Cisco‑compatible QSFP28 ZR4 modules deliver stable links across 50‑60km intermediate‑reach data‑center interconnect routes? A: Yes, the module provides ample optical power margin for 50‑60km DCI applications under RS‑FEC enabled and RX power kept in‑28 ~‑7dBm range. Our internal test results confirm stable error‑free operation even after adding 3‑4dB cumulative splice‑and‑connector loss. This makes the part attractive for procurement teams handling geographically separated campus data‑center interconnection projects.
Q15: Are third‑party compatible 100GBASE‑ZR4 QSFP28 transceivers suitable for carrier‑leased dark‑fiber metro‑DCI circuits on Cisco hardware? A: Yes, HYTOPTODEVICE MSA‑compliant ZR4 works on standard OS2 leased dark‑fiber circuits with mandatory host RS‑FEC turned‑on and received optical power controlled between‑28 ~‑7dBm. Our engineering team offers complimentary link‑budget calculation support for system‑integrator carrier‑customer bids. Always verify total fiber loss before deployment to avoid marginal‑link issues on operator‑provided metro fiber paths
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every module is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.




