| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | SFP-1G-SX | SFP-G31-10LD |
| 2 | Arista Networks | SFP-1G-SX | SFP-G31-40LD |
| 3 | Huawei | eSFP-GE-SX-MM850 | SFP-G55-80LD |
| 4 | Juniper | EX-SFP-1GE-SX | SFP-G55-100LD |
| 5 | Brocade | E1MG-SX-OM | SFP-G55-160LD |
| Huawei Compatible | eSFP-GE-SX-MM850 | Vendor Name | HYTOPTODEVICE |
| Form Factor | SFP | Max Data Rate | 1.25Gbps |
| Wavelength | 850nm | Max Distance | 550m over OM2 MMF |
| Connector | Duplex LC | Transmitter Type | 850nm VCSEL |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -9.0~-3dBm | Receiver Sensitivity | < -18.0dBm |
| Typical Power Consumption | ≤0.8W | Receiver Overload | -3dBm |
| Bit Error Ratio (BER) | 1E-12 | DDM/DOM | Supported |
| Protocols | SFF-8472 MSA Compliant, IEEE 802.3ah-2004 | Operation Temperature | 0°C to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC OM1/OM2/OM3/OM4 MMF (50 or 62.5/125 µm). Do NOT use SMF (OS1/OS2).
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Lock speed to 1.25Gbps (Full Duplex) manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules:MSA hot-swappable. Insert/remove gently without powering down.
Environment:Commercial grade (0°C to 70°C). Avoid extreme heat, moisture, and dust.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Huawei CloudEngine & Campus Switches (S Series): S5720-28X-PWR-SI, S5735-L12T4S-A, S5735-S24T4X, S6730-H24X6C, S7703, S7706
Huawei AR Enterprise Routers: AR161FW, AR2220E, AR2240C, AR6120, AR6140-9G-2AC
Huawei USG Next-Generation Firewalls: USG6620, USG6630, USG6650, USG6712E
Huawei NetEngine (NE) Routers: NE05E, NE20E-S4, NE40E-X3
Main Application Scenarios
Enterprise Local Area Networks (LANs): Interconnecting high-density access layer switches to distribution switches across multi-floor office corporate spaces.
Intra-Data Center Leaf-Spine Links: Patching servers, storage network arrays, and network firewalls directly to adjacent top-of-rack (ToR) switches.
Campus Core Trunks: Serving as high-speed backbone links connecting adjacent buildings, engineering labs, or university server centers where fiber runs stay below 550 meters.
Security & Firewall Integration: Expanding local Gigabit Ethernet throughput links for enterprise security gateways and perimeter hardware.







Q1: What is the maximum distance supported by the Huawei eSFP-GE-SX-MM850 compatible module?
A: It can reach up to 220 meters on legacy OM1 fiber, 550 meters on standard OM2 multi-mode fiber, and up to 1,000 meters (1km) on high-bandwidth OM3 or OM4 laser-optimized multi-mode fiber.
Q2: What does the "e" stand for in eSFP-GE-SX-MM850?
A: The "e" stands for Enhanced. This notation indicates that the SFP module includes built-in Digital Optical Monitoring (DOM) real-time diagnostics, which older basic legacy SFPs lacked.
Q3: Will this third-party module throw compatibility errors on a Huawei CloudEngine switch?
A: No. Our transceivers are hard-coded with the authentic Huawei EEPROM signatures so that the VRP software reads them as native original optics without throwing configuration errors.
Q4: What center operating wavelength does this transceiver use?
A: It transmits and receives inside the short-wave infrared window at a center wavelength of 850nm.
Q5: Can I use this module with Single-Mode Fiber (SMF) patch cords?
A: No. This module is strictly engineered for Multi-Mode Fiber (MMF). Single-mode fiber will cause severe optical loss, preventing the link from establishing.
Q7: Will this 1.25G SX eSFP work with my Huawei switch?
A: Yes, as long as it is coded with the correct Huawei vendor EEPROM firmware. HYTOPTODEVICE Huawei eSFP‑GE‑SX‑MM850 comes pre‑programmed for Huawei platforms; custom EEPROM for other brands is available.
Q8: Can I plug a 1.25G eSFP into a 10G SFP+ port?
A: Yes, provided the 10G port supports dual speeds and is manually forced to 1G. HYTOPTODEVICE Huawei‑compatible eSFP‑GE‑SX‑MM850 supports this mode on multi‑rate Huawei and third‑party switch platforms.
Q9: Is this Huawei‑compatible eSFP‑GE‑SX‑MM850 module MSA compliant?
A: Yes. HYTOPTODEVICE Huawei eSFP‑GE‑SX‑MM850 strictly adheres to SFF‑8472 and eSFP Multi‑Source Agreement standards for broad‑industry interoperability.
Q10: Can I use an 850nm SX eSFP module with Single‑Mode Fiber (SMF)?
A: No. SX optics require Multimode Fiber (MMF). Use an LX eSFP module (1310nm) for SMF. HYTOPTODEVICE offers matching LX eSFP parts for single‑mode gigabit links.
Q11: Will OM3 or OM4 fiber extend the range past 550 meters for eSFP‑GE‑SX‑MM850?
A: No. The 850nm 1000BASE‑SX standard caps link distance at 550m regardless of higher‑grade fiber. HYTOPTODEVICE Huawei‑compatible eSFP‑GE‑SX‑MM850 follows IEEE 802.3z distance limits.
Q12: Does it support DDM / DOM (Digital Diagnostics Monitoring)?
A: Yes, allowing real‑time monitoring of temperature, voltage, TX power, and RX power. HYTOPTODEVICE Huawei eSFP‑GE‑SX‑MM850 exposes DDM data via switch CLI and SNMP.
Q13: What is the typical optical transmit (TX) power for Huawei eSFP‑GE‑SX‑MM850 compatible module?
A: Range is typically between -9.5 dBm and -3.0 dBm. HYTOPTODEVICE Huawei‑compatible eSFP‑GE‑SX‑MM850 is factory‑calibrated within this power window.
Q14: What if DDM reports RX power below -17 dBm?
A: Clean LC connectors, check for fiber damage, and ensure bend radius limits aren't exceeded. HYTOPTODEVICE technical support assists troubleshooting low‑RX‑power issues for bulk orders.
Q15: Does TX/RX polarity matter on fiber patch cords for eSFP‑GE‑SX‑MM850?
A: Yes. TX on Module A must connect to RX on Module B, and vice versa. Reverse polarity will result in no link for HYTOPTODEVICE Huawei eSFP‑GE‑SX‑MM850 compatible transceivers.
Packaging Options & Custom‑Packaging Solutions
Every transceiver module gets reliable ESD‑safe packaging out of the box. Standard packing is ready for immediate shipment, while custom‑printed packaging with your logo is available for bulk orders.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
"We replaced 200 Cisco-branded SFPs with HYTOPTODEVICE equivalents across our spine layer — zero compatibility issues, 40% cost reduction."— Network Architect, Tier-2 ISP, Germany
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final inspection, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



