What Is Brocade Compatible E1MG-SX-OM Optical Transceiver?
SFP Transceiver | Brocade Compatible 1000BASE-SX Optical Transceiver Module(MMF, 850nm, 550m, LC, DOM) | HYTOPTODEVICE
Product Overview
The E1MG-SX-OM is a high-performance, Brocade-compatible sfp optical transceiver. Featuring a hot-pluggable SFP form factor, it operates at a fixed 1Gbps line rate over a 850nm wavelength to transmit data, transmission up to 550m over multi-mode fiber (MMF) vias Duplex LC connector. With high-density networking and low power consumption, this optical module provides highly stable Internet Service Provider (ISP) Gigabit Ethernet communication links, Enterprise LAN & SAN Networks, Data Center LAN & SAN Networks and other optical links. Compliant with both the SFP Multi-Source Agreement (MSA) and IEEE 802.3ah-2004. DOM supported.
Key Technical Specifications
| Brocade Compatible |
E1MG-SX-OM |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP |
Max Data Rate |
1.25Gbps |
| Wavelength |
850nm |
Max Distance |
550m over OM2 MMF |
| Connector |
Duplex LC |
Transmitter Type |
850nm VCSEL |
| Cable Type |
MMF |
Receiver Type |
PIN |
| TX Power |
-9.0~-3dBm |
Receiver Sensitivity |
< -18.0dBm |
| Typical Power Consumption |
≤0.8W |
Receiver Overload |
-3dBm |
| Bit Error Ratio (BER) |
1E-12 |
DDM/DOM |
Supported |
| Protocols |
SFF-8472 MSA Compliant, IEEE 802.3ah-2004 |
Operation Temperature |
0°C to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
-
Fiber Choice: Duplex LC OM1/OM2/OM3/OM4 MMF (50 or 62.5/125 µm). Do NOT use SMF (OS1/OS2).
-
Connector Match: UPC/PC polish only. Do NOT use APC.
-
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
-
Link Setup:Lock speed to 1.25Gbps (Full Duplex) manually if auto-negotiation fails.
-
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
-
Installation & Hot-Swap Rules:MSA hot-swappable. Insert/remove gently without powering down.
-
Environment:Commercial grade (0°C to 70°C). Avoid extreme heat, moisture, and dust.
Links to the Datasheet, User Guide and Compatibility Guides are available on the product page.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
-
Brocade / Ruckus ICX Series: ICX 6430, ICX 6450, ICX 6610, ICX 7150, ICX 7250, ICX 7450, ICX 7650, ICX 7750
-
Brocade FastIron Series: FCX624, FCX648, SX800, SX1600
-
Brocade VDX Series (Data Center): VDX 6740, VDX 6740T, VDX 6940
-
Brocade MLX Series Core Routers: MLX-4, MLX-8, MLX-16
2. Multi-Brand Cross Compatibility
Fully MSA‑compliant, this SFP transceiver module achieves stable interoperability with Cisco, Juniper, Ubiquiti and other third‑party brand gigabit switches, routers and media converters. Custom EEPROM coding available for mixed‑vendor enterprise local‑area network deployment.
3. Free Value-Added Services
-
Custom firmware for multi-device compatibility
-
Free sample testing before bulk orders
-
Complete test reports for project acceptance
-
Strict batch consistency quality control
- Free custom EEPROM programming for special and legacy network environments
Main Application Scenarios
-
Campus Network Backbones: Creating high-speed trunk links to aggregate traffic from access layer switches up to the distribution or core chassis across university or corporate blocks.
-
Intra-Data Center Interconnects: Providing reliable, low-latency cross-connects between top-of-rack (ToR) switches and local storage controllers or server blades.
-
Storage Area Networking (SAN): Hooking up high-density host bus adapters (HBAs) and edge fabrics within small-to-medium Fibre Channel/Ethernet hybrid storage nodes.
-
Enterprise Access Uplinks: Connecting edge switches to secure distribution firewalls or perimeter edge routers.
Connectivity Solutions(Applications)
1.1GbE Switch-to-Switch Connectivity

2.1GbE Switch to Media Converter Connectivity
3.1GbE Structured Cabling Interconnect

4.1GbE Switch-to-NIC Interconnection

The Core Feature
1. High-Efficiency 1G Data Center Interconnect
Engineered for high-density network environments, our SFP-1GE-SX modules deliver plug-and-play 1GbE performance with ultra-low power dissipation—offering a budget-friendly, eco-conscious solution for your daily networking needs.
2.Zero-Downtime Reliability & 100% Brand Compatibility
Rest assured with optical transceivers rigorously benchmarked on over
150+ major brand host switches in our testing lab. Verify your setup instantly via our compatibility sheet—or request a custom, switch-specific
Compatibility Video before you buy.
3.Lab-Certified Quality, Built for Zero Failures
Every transceiver is stress-tested on advanced optoelectronic diagnostics to guarantee signal integrity and long-term stability. Experience full transparency—take a virtual tour of our
Test Center to see our Quality Assurance process in action.

FAQ
Q1: Will using a third-party compatible module void my original Brocade/Ruckus warranty?
A: No. Global consumer protection laws dictate that network equipment brands cannot invalidate hardware system warranties simply because a client utilizes fully compatible third-party optical modules.
Q2: What is the typical power consumption of this short-range SFP?
A: It operates on an extremely efficient thermal and power envelope, typically drawing less than 0.6W to 0.8W during active data routing.
Q3: Does this transceiver comply with multi-source agreements (MSA)?
A: Yes, it is built fully compliant with the SFP MSA standard to ensure reliable universal physical fitment.
Q4: What is the optical link budget for this transceiver?
A: The minimum optical budget is approximately 7.5dB (calculated using a minimum Tx power of -9.5dBm and a minimum receiver sensitivity of -17dBm).
Q5: Is this module safe to handle while the laser is running?
A: It is certified as a Class 1 Laser product, making it safe under normal operation. However, as a rule of thumb, you should never look directly into an active optical aperture.
Q6: What are the safe warehouse storage temperature parameters for this item?
A: Keep it inside an anti-static pouch within an ambient temperature warehouse room tracking between -40°C and 85°C (-40°F to 185°F).
Q7: Does HYTOPTODEVICE E1MG-SX-OM transceiver module support universal brand switch recognition?
A: Yes, as long as it is coded with the correct Brocade vendor EEPROM firmware. HYTOPTODEVICE Brocade E1MG-SX-OM compatible transceiver module comes pre-programmed for Brocade platforms; custom EEPROM for other brands is available.
Q8: Is speed adaptation available when inserting gigabit SFP modules into multi-rate switch ports?
A: Yes, provided the 10G port supports dual speeds and is manually forced to 1G. HYTOPTODEVICE Brocade-compatible transceiver module supports this mode on multi-rate Brocade and third-party switch platforms.
Q9: What industry standard specifications govern this Brocade gigabit SX transceiver?
A: Yes. HYTOPTODEVICE Brocade E1MG-SX-OM compatible transceiver module strictly adheres to SFF-8472 and SFP Multi-Source Agreement standards for broad-industry interoperability.
Q10: Why cannot 850nm SX optical modules work with single-mode fiber cabling?
A: No. SX optics require Multimode Fiber (MMF). Use an LX transceiver module (1310nm) for SMF. HYTOPTODEVICE offers matching LX SFP parts for single-mode gigabit links.
Q11: Does advanced graded multimode fiber increase 1000BASE-SX maximum transmission range?
A: No. The 850nm 1000BASE-SX standard caps link distance at 550m regardless of higher-grade fiber. HYTOPTODEVICE Brocade-compatible transceiver module follows IEEE 802.3z distance limits.
Q12: What monitoring functions are integrated on Brocade E1MG-SX-OM transceiver modules?
A: Yes, allowing real-time monitoring of temperature, voltage, TX power, and RX power. HYTOPTODEVICE Brocade E1MG-SX-OM compatible transceiver module exposes DDM data via switch CLI and SNMP.
Q13: What calibrated optical output power range comes with this Brocade compatible SFP?
A: Range is typically between -9.5 dBm and -3 dBm. HYTOPTODEVICE Brocade-compatible transceiver module is factory-calibrated within this power window.
Q14: What troubleshooting steps fix low received optical power on SX multimode links?
A: Clean LC connectors, check for fiber damage, and ensure bend radius limits aren't exceeded. HYTOPTODEVICE technical support assists troubleshooting low-RX-power issues for bulk orders.
Q15: Why correct TX/RX wiring polarity is critical for SFP fiber link activation?
A: Yes. TX on Module A must connect to RX on Module B, and vice versa. Reverse polarity will result in no link for HYTOPTODEVICE Brocade E1MG-SX-OM compatible transceiver module.
Packaging Options & Custom‑Packaging Solutions
Every transceiver module gets reliable ESD‑safe packaging out of the box. Standard packing is ready for immediate shipment, while custom‑printed packaging with your logo is available for bulk orders.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- 100% MSA-compliant modules with Cisco, Huawei,Dell,Juniper, and Arista compatibility
- ISO 9001:2015 certified manufacturing facility in Shenzhen
- Average lead time of 3–5 business days with DHL/FedEx express options
- Dedicated pre-sales engineering support for custom configurations
- Actual hardware,actual switches,actual results.we publish compatibility test video,eliminate compatibility anxiety. you can watch before you buy.
- We can provide inspection and shipping videos to make you feel as if you are right here with the product.
"We replaced 200 Cisco-branded SFPs with HYTOPTODEVICE equivalents across our spine layer — zero compatibility issues, 40% cost reduction."— Network Architect, Tier-2 ISP, Germany
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final inspection, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration
