| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | DELL | 430-4593 | QSFP-40G-SR4(Cisco) |
| 2 | EdgeCore | ET6401-SR4 | QSFP-40G-SR4(Huawei) |
| 3 | Extreme | 10319 | QSFP-40G-IR4 |
| 4 | HPE Aruba | JH231A | QSFP-40G-LG4 |
| 5 | H3C | QSFP-40G-SR4-MM850 | QSFP-40G-ER4 |
| 6 | HPE BladeSystem | 720187-B21 | QSFP-40G-ZR4 |
| 7 | HPE H3C | JG325A | QSFP-40G-CSR4 |
| 8 | F5 Networks | F5-UPG-QSFP+ |
| HPE BladeSystem Compatible | 720187-B21 | Vendor Name | HYTOPTODEVICE |
| Form Factor | QSFP+ | Max Data Rate | 41.25Gbps |
| Wavelength | 850nm | Max Distance | 150m@OM4/100m@OM3 |
| Connector | MTP/MPO | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -8.0~1.0dBm | Receiver Sensitivity | < -13dBm |
| Power Consumption | ≤1.5W | Modulation | NRZ |
| Protocols | IEEE 802.3 40GBASE-SR4, SFF-8436 | Operation Temperature | 0 to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
Fiber Choice: Only compatible with OM3 / OM4 multi‑mode MPO‑12 trunk cabling; single‑mode fiber cannot facilitate 850 nm SR4 operation and will produce link failure.
Distance Limit: 100‑metre maximum operating reach on OM3, 150‑metre maximum on OM4; excessive splice joints, dirty connector end‑faces or sharp fiber bends degrade practical transmission distances.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Installation Specification: Hot‑plug supported; keep MPO connector end‑faces clean, observe minimum fiber‑bend radius requirements.
Operating Environment: Designed for commercial‑grade 0°C‑70°C ambient conditions; maintain adequate cabinet‑level airflow to prevent excessive module temperature build‑up.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
Primary Application Scenarios
• Short‑haul fabric uplink connections for HPE BladeSystem c‑Class c7000 / c3000 chassis environments
• 40G high‑speed uplink expansion for Virtual Connect FlexFabric interconnect modules
• Chassis‑to‑external‑switch short‑range multi‑mode fiber trunk links inside blade‑server server halls
• Rack‑to‑rack inter‑chassis connections for consolidated blade‑compute pools
• Enterprise infrastructure refresh and BladeSystem c‑Class modernisation initiatives
• Multi‑vendor mixed‑fabric deployments combining blade‑chassis and top‑of‑rack switching hardware




1. 40G Connectivity for Data Center
High speed, low overhead. The QSFP+ 40G module brings gigabit-class throughput to dense data center racks while drawing less power and taking up less space.



FAQ
Q1: How should operators resolve unrecognised‑transceiver alerts once HYTOPTODEVICE QSFP+ 40G SR4 is installed inside HPE BladeSystem c‑Class interconnect bays? A: This usually means the module's coding does not match the switch's vendor lock. Genuine‑compatible HYTOPTODEVICE modules include the right coding; if the message persists, check the port configuration, update firmware, or contact us for a recode.
Q2: Can HYTOPTODEVICE 40G SR4 hardware work alongside existing 10G SFP+ gear to implement staged BladeSystem infrastructure transition projects? A: Yes, with a breakout solution: the 40G SR4 can be split into 4×10G links using an MPO‑to‑4×LC breakout cable connected to SFP+ ports, letting you migrate gradually.
Q3: Which fiber varieties are suitable when deploying HYTOPTODEVICE BladeSystem‑compatible QSFP+ 40G SR4 optical hardware in blade‑compute data‑centers? A: Multimode fiber only — OM3 or OM4 (OM5 also supported on some platforms). It will not work on single‑mode fiber; that requires a 40G LR4 module.
Q4: What power draw levels should infrastructure planners anticipate for HYTOPTODEVICE QSFP+ 40G SR4 modules populated within BladeSystem interconnect bays? A: Typically around 1.0–1.5 W per module, depending on vendor and temperature — far lower than the MSA maximum, so it is safe for dense interconnect line‑cards.
Q5: What insertion loss and link‑budget parameters need evaluation while designing cabling plant for HYTOPTODEVICE 40G SR4 Blade‑System deployments? A: The 40GBASE‑SR4 channel supports a maximum insertion loss of about 1.9 dB (including connectors and patch panels). Confirm your cable plant loss before deployment.
Q6: Will deploying HYTOPTODEVICE 40G SR4 hardware impose constraints over prospective 100G‑upgrade roadmaps for Blade‑System‑based compute environments? A: It is a 40G product; the fiber (OM3/OM4) can often be reused for 100G SR4/SR10, but the module and ports must be upgraded. Plan cabling with future capacity in mind.
Q7: Am I able to reuse existing on‑premises MPO trunk cabling alongside HYTOPTODEVICE QSFP+ 40G SR4 for BladeSystem modernisation projects? A: Check the fiber count, connector polish (UPC), and polarity. Existing 12‑fiber MPO trunks are often reusable, but verify loss and polarity against SR4 requirements.
Q8: What operational risks emerge should I combine OM3 and OM4 multi‑mode fiber segments within one physical link utilising HYTOPTODEVICE 40G SR4 transceivers? A: Yes, but the reach is limited by the shorter‑grade segment (OM3), so a mixed link is rated at 100 m maximum.
Q9: What sorts of compliance documentation can enterprise purchasers obtain for HYTOPTODEVICE factory‑bulk‑ordered QSFP+ 40G SR4 optical units? A: Typical certifications include CE, FCC, RoHS, and REACH compliance; some suppliers also hold ISO 9001. Ask for certificates before ordering.
Q10: Do HYTOPTODEVICE QSFP+ 40G SR4 optical units feature adequate ESD safeguards throughout packaging and field‑handling workflows for BladeSystem bay installations? A: Yes — they ship in anti‑static packaging and are designed for hot‑swap with ESD protection. Always ground yourself before handling.
Q11: What stock readiness and fulfilment lead‑times apply for HYTOPTODEVICE BladeSystem‑compatible 40G SR4 factory bulk purchase orders? A: Popular models (Cisco/Arista/Juniper‑compatible 40G SR4) are usually in stock with 24–72 h dispatch; custom‑coded or industrial versions may take 1–3 weeks.
Q12: Which settlement choices and international shipping Incoterm arrangements can HYTOPTODEVICE accommodate for cross‑border factory wholesale QSFP+ 40G SR4 procurement? A: Typical terms: T/T, PayPal, or trade assurance for smaller orders; FOB, CIF, or DDP for freight. Confirm total landed cost (shipping, duties, taxes) before finalizing.
Q13: Are there unforeseen extra expenditures such as import levies when importing HYTOPTODEVICE QSFP+ 40G SR4 for Blade‑System‑based enterprise projects? A: Duties and taxes vary by destination and Incoterm. Ask the supplier to quote DDP if you want a fixed, all‑inclusive delivered price with no surprises at customs.
Q14: How can Blade‑System administrators pull real‑time optical performance metrics out of HYTOPTODEVICE QSFP+ 40G SR4 working within HPE Onboard Administrator environment? A: Use the switch CLI (e.g., show interface transceiver or show optics) to view per‑lane temperature, voltage, TX/RX power, and alarms — the data comes from the module's standard DOM.
Q15: Does procuring 40G SR4 hardware remain a sound strategic investment given industry transition toward 100G / 400G speeds for HPE Blade‑System compute infrastructures? A: For existing 40G networks it remains fully supported and cost‑effective; your multimode cabling can often be reused later. Choose suppliers with long‑term availability so you can restock for years.
Packaging & Custom OEM Solutions
Every QSFP+ SR4 module ships in sealed ESD-safe packaging, ready for same-day dispatch. Bulk orders offer OEM customization—logo printing and private labeling—tailored for network distributors, integrators, and enterprise deployments.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP+ modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



