| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | GLC-TA | SFP-GE-T |
| 2 | Alcatel-Lucent | iSFP-GIG-T | SFP-GIG-T |
| 3 | Brocade | E1MGTX-A | GLC-TE-I |
| 4 | Extreme | 10065 | SFP-10G-T-30 |
| 5 | Juniper Networks | EX-SFP-1GE-T | SFP-10G-T-30I |
| 6 | MikroTik | S-RJ01 | SFP-10G-T-80 |
| 7 | Ciena | XCVR-B00CRJ | SFP-10G-T-100 |
| 8 | Finisar | FCLF8522P2BTL |
Product Overview
HYTOPTODEVICE Finisar FCLF8522P2BTL compatible copper SFP module delivers flexible triple-speed 10/100/1000BASE-T Ethernet transmission over twisted-pair copper cabling. This hot-swappable SFP copper module with RJ45 connector supports up to 100-meter links over Cat5e/Cat6 cable and uses SGMII host interface for seamless communication with network switches and routers. Built to IEEE 802.3 & SFP MSA standards, pre-programmed EEPROM enables plug-and-play recognition for Finisar-based platforms without unsupported transceiver warning logs. This copper SFP module supports auto-negotiation for 10Mbps,100Mbps and 1000Mbps speeds. HYTOPTODEVICE manufactures this copper SFP module for network distributors, system integrators and bulk purchasers.
Key Technical Specifications
| Finisar Compatible | FCLF8522P2BTL | Vendor Name | HYTOPTODEVICE |
| Form Factor | SFP | Data Rate | 10/100/1000Mbps |
| Connector | RJ-45 | Cable Distance | 100m |
| Media | Copper | Cable Type | Cat 5e/6/6a (UTP) |
| Max. Power Consumption | ≤1.2W | DDM Support | YES |
| Protocols | MSA Compliant, IEEE STD 802.3 and 802.3ab | Operation Temperature | -40 to 85°C (-40 to 185°F) |
Standard: Cat5e or Cat6 twisted-pair cable is required to achieve full 100-meter Gigabit performance.
Note: Standard Cat5 cable may limit link stability at full 1G speed and is not recommended.
Live Insertion: The SFP RJ45 transceiver supports live insertion and removal.
Precaution: Avoid repeated hot swapping under continuous heavy traffic loads to ensure optimal hardware longevity.
Heat Dissipation: This 1Gbps copper module generates mild heat during operation.
Deployment Advice: Verify the switch thermal budget and ensure adequate ventilation before fully populating all SFP ports.
Fixed Rate: This RJ45 transceiver operates at a fixed 1000Mbps speed only.
Compatibility Warning: It cannot auto-negotiate down to 100Mbps or 10Mbps. The connected peer device must support 1G speed to successfully establish a link.
Storage Environment: Keep unused transceivers stored in dry, ESD-safe packaging.
Dust Protection: Always fit dust caps onto the RJ45 port when the module is not in service.
Built on SFP MSA and IEEE industry standards, this RJ45 SFP Transceiver module also works with Fortinet, Dell, Extreme and other mainstream network hardware, suitable for mixed-brand enterprise and campus network renovation projects.



The Core Features



FAQ
Q1: Can this copper SFP module automatically negotiate different speeds between 10M,100M and 1000M?
A: Yes, this copper SFP module supports auto-negotiation for 10/100/1000BASE-T. HYTOPTODEVICE Finisar FCLF8522P2BTL compatible copper SFP module automatically matches the speed of connected peer devices over Cat5e/Cat6 cabling. It brings flexible deployment for mixed-speed legacy LAN environments where gigabit and fast ethernet devices coexist.
Q2: Do I need SGMII support on the host switch to run this copper SFP module properly?
A: Yes, host hardware must provide SGMII interface to operate this copper SFP module. This Finisar compatible copper SFP module relies on SGMII to transfer signals between switch PHY and copper transceiver. The module cannot work if the SFP port only supports 1000BASE-X without SGMII.
Q3: What cable types are acceptable to reach the full 100m distance for this copper SFP module?
A: Cat5e or Cat6 twisted pair cables are required for full 100m reach of this copper SFP module. HYTOPTODEVICE copper SFP module follows IEEE 802.3 standard, and older Cat5 cable may cause signal attenuation, crosstalk and unstable link when running near maximum distance.
Q4: Will this copper SFP module work for cross-brand connections between different vendor switches?
A: Yes, this copper SFP module supports multi-brand interoperability under IEEE and SFP MSA standards. HYTOPTODEVICE Finisar FCLF8522P2BTL compatible copper SFP module can connect switches from different brands, as long as both sides have SGMII SFP ports and support 10/100/1000BASE-T.
Q5: Is MDI/MDIX auto crossover built inside this copper SFP module?
A: Yes, this copper SFP module includes auto MDI/MDIX function. You can use straight-through patch cables directly without crossover cables for switch-to-switch or switch-to-server connections. This feature simplifies on-site cabling work for LAN installers deploying HYTOPTODEVICE copper SFP module.
Q6: What power consumption should I expect when installing multiple copper SFP module in a dense switch chassis?
A: Each copper SFP module consumes typical ~1.05W power. Low power design minimizes heat buildup on high-density switch ports. For chassis switches, you can calculate total power budget easily when you deploy multiple HYTOPTODEVICE copper SFP module in all available SFP slots.
Q7: Can I use this copper SFP module to connect IP cameras and VoIP phones in enterprise LAN?
A: Yes, this copper SFP module works perfectly for IP camera and VoIP phone LAN links. The triple-speed auto-negotiation can adapt to 100M for legacy cameras and 1G for newer devices. HYTOPTODEVICE copper SFP module converts SFP SGMII port to standard RJ45 port to connect these end devices.
Q8: Does this copper SFP module support DDM digital diagnostic monitoring to read real-time parameters?
A: No, this copper SFP module does not support DDM/DOM monitoring functions. Unlike optical transceivers, this RJ45 copper SFP module does not include optical power monitoring. You can check link status directly from the switch management page after installing HYTOPTODEVICE copper SFP module.
Q9: What is the difference between this triple-speed copper SFP module and fixed 1000BASE-T only copper SFP module?
A: This copper SFP module supports 10/100/1000 auto negotiation, while fixed 1000BASE-T copper SFP module only runs gigabit speed. HYTOPTODEVICE Finisar FCLF8522P2BTL compatible copper SFP module fits mixed-speed legacy networks, where many end devices only support 100Mbps Fast Ethernet.
Q10: Can I hot swap this copper SFP module while the switch remains powered and online?
A: Yes, this copper SFP module supports hot swap as defined by SFP MSA. You can insert or remove HYTOPTODEVICE copper SFP module without powering down the host switch. Still, avoid frequent repeated hot-plug operations to reduce mechanical wear of the SFP connector.
Q11: Will ceiling plenum temperature and humidity fluctuations degrade links running on this copper SFP module?
A: Within rated 0~70°C operating range, this copper SFP module maintains stable links. Extreme high humidity and temperature swings will degrade copper cable performance rather than the module itself. Use plenum-rated Cat5e/Cat6 cables and keep adequate ventilation for HYTOPTODEVICE copper SFP module deployments inside ceiling spaces.
Q12: Does 802.1X port access control function normally on ports fitted with this copper SFP module?
A: Yes, 802.1X authentication works normally with this copper SFP module. The authentication logic runs inside the host switch firmware, and HYTOPTODEVICE copper SFP module simply passes Ethernet frames without interfering security traffic. You can apply port-based network access policies normally.
Q13: What will happen if the power supply fails on a switch populated with this copper SFP module?
A: Without redundant power supply, the whole switch will power off and drop all links using this copper SFP module. Deploy dual power supplies for critical enterprise LAN segments. HYTOPTODEVICE copper SFP module itself does not provide power backup function.
Q14: Can network monitoring tools capture mirrored traffic over links using this copper SFP module?
A: Yes, port mirroring works normally on links equipped with this copper SFP module. The HYTOPTODEVICE copper SFP module forwards mirrored Ethernet packets without modification. Network technicians can connect packet analyzers to monitor traffic for troubleshooting and network audit.
Q15: Can I order custom EEPROM coding for this copper SFP module to match my host hardware?
A: Yes, HYTOPTODEVICE offers free custom EEPROM programming service for this copper SFP module. We can customize EEPROM data to match Finisar FCLF8522P2BTL identity to eliminate transceiver warning logs on your target network hardware for bulk orders.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every module is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.




