Cisco Compatible Industrial SFP-10G-BXU-I 10G BiDi SFP+ Transceiver Module 10GBASE-BX20-U (SMF, 1270nm-TX/1330nm-RX, 20km, LC, DDM)
Product Overview
The Cisco compatible SFP-10G-BXU-I optical transceiver features an LC simplex connector and supports up to 20km transmission over G.652 single-mode fiber. This 10g bidi sfp+ transceiver realizes bidirectional data transmission through just one fiber strand, helping you cut cabling expenses and make full use of existing fiber resources. Manufactured by HYTOPTODEVICE, the 10GBASE-BX20-U 10g bidi sfp+ transceiver fully meets SFP+ MSA, IEEE 802.3ae and SFF-8431 specifications. In addition, this 10G fiber optic transceiver integrates DDM digital diagnostic monitoring to view real-time running parameters. It also offers full plug-and-play compatibility with Cisco and more than 150 mainstream brand network devices.
Key Technical Specifications
| Cisco Compatible |
SFP-10G-BXU-I |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP+ |
Max Data Rate |
10.7Gbps |
| Wavelength |
TX1270nm/RX1330nm |
Max Distance |
20km |
| Connector |
Simplex LC |
Transmitter Type |
1270nm DFB |
| Cable Type |
SMF |
Receiver Type |
PIN |
| TX Power |
-3.0~+2.0dBm |
Receiver Sensitivity |
< -14.4dBm |
| Max. Power Consumption |
≤1W |
Receiver Overload |
0.5dBm |
| Protocols |
10G Ethernet, MSA Compliant |
Operation Temperature |
-40 to 85°C (40 to 185°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Operational Best Practices
•
BiDi Pairing Rule: SFP‑10G‑BXU (Tx1270/Rx1330) must pair with
SFP‑10G‑BXD (Tx1330/Rx1270) at remote end. Two BXU modules will NOT form a valid link.
•
Cabling Requirement: Use OS2 single‑mode simplex‑LC UPC cables only. Multimode fiber / APC connectors reduce reach and cause link issues; keep connectors clean.
•
Port Notice: Install only into standard SFP+ ports. Do not force into 1G‑SFP slots. Disable transceiver‑block policy if needed on host devices.
•
Environment: Run within 0‑70 °C. Avoid high‑heat, dusty, poorly ventilated rack positions.
•
Hot‑swap: Supports hot‑swap; disconnect fiber before plugging / unplugging to protect optical ports.
•
DDM Monitoring: Enable DDM/DOM; monitor optical power and temperature for early fault warning.
•
Pre‑test Recommendation: Test sample units with real hardware before large‑scale bulk deployment.
•
Laser Safety: Avoid direct eye exposure to powered optical ports; infrared laser can harm eyes.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Multi-Brand Supported Network Hardware
1.Cisco Dedicated Compatible Platforms & Supported Models
Our plug and play 10g bidi sfp+ transceiver is pre-programmed with standard Cisco EEPROM identification data, eliminating unsupported transceiver warning logs on all listed physical hardware after full real-machine insertion verification:
-
Cisco Industrial Ethernet (IE) Series: IE3400, IE3400H, IE4010, and IE5000 ruggedized switches.
-
Cisco Catalyst Series (Outdoor/Industrial): Catalyst 9300 (with industrial modules) and Catalyst IE9300 Rugged Series.
-
Cisco ASR & NCS Routers: ASR 900 Series and NCS 540 for cell site aggregation.
-
Cisco Connected Grid Routers: CGR 2010 for utility and smart grid applications.
-
Standard Enterprise Support: Also compatible with Catalyst 9200/9500 and Nexus switches requiring industrial-spec optics.
2. Cross‑Brand Interoperability
Built on MSA open standards, this 10G BiDi SFP+ works with Cisco, Arista, Juniper, H3C, Huawei, Brocade, Dell hardware. Well‑suited for mixed‑vendor metro and DCI expansion projects for enterprise, carrier clients, wholesalers and integrators.
Primary Application Scenarios
- 10g bidi sfp+ transceiver for campus single fiber backbone, cutting fiber cabling expenses in half for long-distance point-to-point enterprise network upgrades with simplex single-strand OS2 fiber.
- 10g bidi sfp+ transceiver for enterprise switch to NIC uplink, building stable 10G single-fiber high-speed connections between core rack switches and local server network interface cards.
- 10g bidi sfp+ transceiver for structured cabling rack deployment, matching standardized cable management layouts for indoor server rooms and multi-floor building wiring infrastructure.
- Bulk wholesale industrial grade 10g bidi sfp+ transceiver for outdoor industrial monitoring systems, operating stably in unconditioned field cabinets with wide -40~85℃ temperature tolerance.
- Cost-saving 10g bidi sfp+ transceiver for ISP FTTB access network construction, reducing large-batch purchasing costs compared with high-priced original Cisco OEM optical modules.
Connectivity Solutions(Applications)
1.10G Switch-to-Switch Interconnection Diagram:

2.10G Switch-to-NIC Interconnection Diagram:

3.10G Structured Cabling Rack Layout Diagram:

The Core Features
1.Slash Cabling Costs with Single-Fiber BiDi
Stop paying for extra optical fibers. Our 10G BiDi SFP+ transceivers send and receive data over one single strand of fiber, helping you slash cabling infrastructure costs while fully utilizing your current deployment.

2.Instantly Double Your Bandwidth
Run out of fiber lines? No problem. By separating transmit and receive wavelengths on a single strand, this module instantly doubles your network capacity without requiring you to pull any new cables.

3.1W Low-Power 10G Link
Power consumption matters in high-density data centers. Featuring a highly efficient design, this 10G SFP+ module operates at under 1W, minimizing heat generation and lowering your overall operational and cooling costs.

4.Seamless Cross-Brand Interoperability
Eliminate compatibility headaches. We test every single module in actual, real-world mainstream switches to guarantee flawless cross-brand interoperability. Want proof? Specific Compatibility Video available upon request.

5.Rigorously Tested for Zero-Downtime Reliability
We don’t compromise on network uptime. Through comprehensive testing—including temperature, signal integrity, and optical power analysis—before leaving our Test Center. we ensure your 10G BiDi 10km links remain rock-solid and packet-loss-free.

FAQ
Q1: What does the "-I" stand for in Cisco SFP-10G-BXU-I?
A: The "-I" stands for Industrial Temperature Range. While standard optics operate between 0°C and 70°C, this industrial-grade 10G SFP+ is rated for -40°C to 85°C (-40°F to 185°F), ensuring stability in extreme heat or cold.
Q2: Which module must be paired with the SFP-10G-BXU-I?
A: To establish a link, you must pair this module with the SFP-10G-BXD-I (Downstream). The BXD-I transmits at 1330nm and receives at 1270nm to complete the bidirectional circuit.
Q3: Can I use this industrial module in a standard Cisco Catalyst switch?
A: Yes. Industrial-grade optics are backwards compatible with commercial switches. They provide an extra layer of reliability even in climate-controlled server rooms.
Q4: Does the HYTOPTODEVICE version support Cisco Digital Optical Monitoring (DOM)?
A: Absolutely. It supports full DOM, allowing you to monitor real-time temperature, voltage, and optical power via the Cisco CLI command show inventory and show interfaces transceiver detail.
Q5: Is this module hot-swappable in industrial environments?
A: Yes. The module is hot-pluggable, allowing for maintenance or upgrades in Cisco IE switches without powering down the device, which is vital for maintaining industrial uptime.
Q6: Does industrial single strand 10G bidi SFP+ transceiver require duplex LC fiber jumpers for data transmission?
A: No. Every HYTOPTODEVICE 10G bidi SFP+ transceiver uses a simplex LC port. Bidirectional 10G traffic transmits via just one single-mode fiber strand, so duplex fiber cords are unnecessary.
Q7: What ambient temperature range supports stable running of wide temp rated 10G bidi SFP+ transceiver Tx1270/Rx1330?
A: This HYTOPTODEVICE SFP-10G-BXU-I industrial 10G bidi SFP+ transceiver works steadily from -40°C to 85°C. It fits unheated outdoor cabinets and harsh industrial field environments.
Q8: Is Tx1270 Rx1330 20km 10G bidi SFP+ transceiver functional over OM1/OM2 multimode fiber wiring?
A: Not compatible. Our 10G bidi SFP+ transceiver’s laser and receiver are tuned exclusively for OS1/OS2 single-mode fiber. Links will fail completely on multimode cabling.
Q9: Do short-distance 6km single-fiber links need inline attenuator for high-power industrial 10G bidi SFP+ transceiver?
A: Yes. This HYTOPTODEVICE 10G bidi SFP+ transceiver delivers up to 6dBm transmit power. For links shorter than 10km, install a 5–10dB LC attenuator to avoid receiver saturation and hardware damage.
Q10: Can Cisco pre-coded 10G bidi SFP+ transceiver read full DOM diagnostic data via standard IOS CLI commands?
A: Absolutely. All HYTOPTODEVICE 10G bidi SFP+ transceiver fully complies with SFF-8472 DOM standards. Engineers check real-time Tx/Rx power, temperature and voltage through Cisco built-in transceiver detail commands.
Q11: Is pluggable industrial 10G bidi SFP+ transceiver hot-swappable on powered-on Cisco Catalyst switches without traffic loss?
A: Yes. HYTOPTODEVICE 10G bidi SFP+ transceiver supports full hot-swap capability. Insert or remove modules from live 10G SFP+ slots without rebooting switches or disrupting existing network traffic.
Q12: Will deploying third-party programmed 10G bidi SFP+ transceiver void official Cisco network equipment warranty?
A: No. The Magnuson-Moss Warranty Act forbids Cisco from invalidating hardware warranty only for using qualified aftermarket optics. HYTOPTODEVICE pre-tested 10G bidi SFP+ transceiver brings zero warranty risks.
Q13: How to eliminate unsupported transceiver warning logs for Cisco matched 10G bidi SFP+ transceiver Tx1270/Rx1330?
A: The alert is a harmless system label with no impact on link performance. If ports get error-disabled, input two simple IOS CLI commands to remove restrictions for our HYTOPTODEVICE 10G bidi SFP+ transceiver.
Q14: What wavelength pairing difference separates upstream and downstream industrial 10G bidi SFP+ transceiver modules?
A: HYTOPTODEVICE SFP-10G-BXU-I 10G bidi SFP+ transceiver transmits at 1270nm and receives at 1330nm, while the matching SFP-10G-BXD-I sends 1330nm and receives 1270nm; the two models must work as a matched pair.
Q15: Can two identical upstream SFP-10G-BXU-I 10G bidi SFP+ transceiver establish valid single-fiber point-to-point links?
A: Impossible. Two same BXU 10G bidi SFP+ transceiver will transmit signals on the identical wavelength, so neither module can receive return signals, resulting in permanent down link status.
Packaging & Custom OEM Solutions
Each module is individually sealed in ESD-safe anti-static packaging and ready for immediate shipment. For high-volume distributors, wholesalers, and system integrators, we offer flexible OEM programs—including custom logos, private labeling, and branded packaging—to help you build and protect your own brand.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

Others


