Arista 10GBASE-ERBD-U Compatible Industrial SFP+ BiDi 10G 40km Module 10GBASE-BX40-U (SMF, 1270nm-TX/1330nm-RX, 40km, Simplex LC, DDM)
Product Overview
Our HYTOPTODEVICE Arista 10GBASE-ERBD-U Compatible SFP+ BiDi 10G 40km module is single strand 10G SFP+ transceiver, built for 40km point-to-point transmission over single strand OS2 single mode fiber.
• Wavelength: Tx1270nm/Rx1330nm (Match Arista 10GBASE-ERBD-D standard BiDi pairing)
• Interface: Standard LC simplex connector
• Transmission Distance: Stable 40km @10Gbps SMF OS2
Compliant with Hot-Pluggable SFP+ MSA, SFF-8472,SFP-8431, IEEE 802.3ae and RoHS standards and fully DDM/DOM support, Delivering high-speed performance with optimized power efficiency, this single-strand SFP+ BiDi 10G 40km module is the ideal solution for cross-campus backbones, metropolitan area network (MAN) rings, and long-range data center interconnects (DCI). We support samples, bulk wholesale and OEM private labeling, submit bulk inquiry or RFQ for competitive pricing and long-term supply contracts.
Key Technical Specifications
| Arista Compatible |
10GBASE-ERBD-U |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP+ |
Max Data Rate |
10.7Gbps |
| Wavelength |
TX1270nm/RX1330nm |
Max Distance |
40km |
| Connector |
Simplex LC |
Transmitter Type |
1270nm DFB |
| Cable Type |
SMF |
Receiver Type |
PIN |
| TX Power |
-1.0~+5dBm |
Receiver Sensitivity |
< -15dBm |
| Max. Power Consumption |
≤1W |
DOM/DDM |
Fully Supported |
| Protocols |
SFP+ MSA, SFF-8472, IEEE 802.3ae, RoHS Compliant |
Operation Temperature |
0 to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Operational Best Practices
•
BiDi Pairing Rule: SFP‑10G‑BXU (Tx1270/Rx1330) must pair with
SFP‑10G‑BXD (Tx1330/Rx1270) at remote end. Two BXU modules will NOT form a valid link.
•
Cabling Requirement: Use OS2 single‑mode simplex‑LC UPC cables only. Multimode fiber / APC connectors reduce reach and cause link issues; keep connectors clean.
•
Port Notice: Install only into standard SFP+ ports. Do not force into 1G‑SFP slots. Disable transceiver‑block policy if needed on host devices.
•
Environment: Run within 0‑70 °C. Avoid high‑heat, dusty, poorly ventilated rack positions.
•
Hot‑swap: Supports hot‑swap; disconnect fiber before plugging / unplugging to protect optical ports.
•
DDM Monitoring: Enable DDM/DOM; monitor optical power and temperature for early fault warning.
•
Pre‑test Recommendation: Test sample units with real hardware before large‑scale bulk deployment.
•
Laser Safety: Avoid direct eye exposure to powered optical ports; infrared laser can harm eyes.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Network Hardware
1. Validated Arista Hardware & Firmware
HYTOPTODEVICE 10G BiDi SFP+ modules use Arista‑tuned EEPROM profiles for seamless plug‑and‑play on Arista EOS platforms. Each unit passes real‑machine validation, temperature cycling and 72‑hour burn‑in. Free EEPROM re‑flash and OEM branding are offered for bulk distributors and integrators.
Validated Arista‑oriented Platforms:
• Arista 7050 / 7060 / 7280 series data‑center switches
• Arista 7300 series modular chassis switches
• All Arista network devices with standard SFP+ ports supporting 10GBASE‑ERBD BiDi specification
2. Cross‑Brand Interoperability
Built on MSA open standards, this 10G BiDi SFP+ works with Cisco, Huawei, H3C, Juniper, Dell, Palo Alto, Brocade hardware. Well‑suited for mixed‑vendor metro and DCI expansion projects for enterprise, carrier clients, wholesalers and integrators.
Primary Application Scenarios
Versatile SFP+ BiDi 10G 40km module for low-cost, long-distance 10G single-fiber network deployment.
1. Data center Arista switch long-distance 10G uplink, adopting SFP+ BiDi 10G 40km module to simplify single-fiber cabling
2. Multi-building enterprise campus 40km 10G interconnection, saving fiber resources with single-strand SFP+ BiDi 10G 40km module
3. Outdoor industrial cabinet 10G fiber transmission, utilizing industrial-grade SFP+ BiDi 10G 40km module for extreme temperature adaptation
4. ISP last-mile broadband and remote base station 10G networking with cost-effective SFP+ BiDi 10G 40km module
5. Enterprise 10G structured cabling projects, reducing construction costs via single-fiber SFP+ BiDi 10G 40km module deployment
Connectivity Solutions(Applications)
1.Switch-to-Switch 10G BiDi Single Fiber Uplink

2.Switch-to-10G SFP+ NIC Server Long Distance Link

3.Enterprise 10G Single Fiber Structured Cabling System Layout

The Core Features
1.Slash Cabling Costs with Single-Fiber BiDi
Stop paying for extra optical fibers. Our 10G BiDi SFP+ transceivers send and receive data over one single strand of fiber, helping you slash cabling infrastructure costs while fully utilizing your current deployment.

2.Instantly Double Your Bandwidth
Run out of fiber lines? No problem. By separating transmit and receive wavelengths on a single strand, this module instantly doubles your network capacity without requiring you to pull any new cables.

3.1W Low-Power 10G Link
Power consumption matters in high-density data centers. Featuring a highly efficient design, this 10G SFP+ module operates at under 1W, minimizing heat generation and lowering your overall operational and cooling costs.

4.Seamless Cross-Brand Interoperability
Eliminate compatibility headaches. We test every single module in actual, real-world mainstream switches to guarantee flawless cross-brand interoperability. Want proof? Specific Compatibility Video available upon request.

5.Rigorously Tested for Zero-Downtime Reliability
We don’t compromise on network uptime. Through comprehensive testing—including temperature, signal integrity, and optical power analysis—before leaving our Test Center. we ensure your 10G BiDi 40km links remain rock-solid and packet-loss-free.

FAQ
Q1: Why do brand new Arista 10GBASE-ERBD-U compatible SFP+ BiDi 10G 40km module fail to establish any link after dual-end installation?
A: Total dead links are almost always caused by mismatched BiDi wavelength pairing. Same-type modules cannot communicate. HYTOPTODEVICE SFP+ BiDi 10G 40km module strictly requires Tx1270/Rx1330 paired with Tx1330/Rx1270; we supply pre-tested matched pairs to eliminate onsite pairing errors.
Q2: Can I substitute two TX1270nm SFP+ BiDi 10G 40km modules for temporary short-distance fiber links without TX1330 modules?
A: No. Dual identical wavelength BiDi modules cause mutual signal collision and zero data exchange. All HYTOPTODEVICE SFP+ BiDi 10G 40km module pairs are factory-calibrated with standard opposite wavelengths to guarantee valid bidirectional transmission.
Q3: Will industrial SFP+ BiDi 10G 40km module support stable transmission on extended 42km over-limit fiber routes?
A: No. The HYTOPTODEVICE SFP+ BiDi 10G 40km module features a fixed 40km optical power budget with no extra attenuation margin. Any distance exceeding 40km results in unstable signal loss and complete link dropout.
Q4: Why do stable 40km BiDi links drop after adding intermediate patch panels on long fiber runs?
A: SFP+ BiDi 10G 40km module power budget is highly sensitive to extra insertion loss. Additional patch panels or poor splicing exceed the tight loss tolerance. HYTOPTODEVICE optimizes optical sensitivity for standard-loss cabling environments to maintain reliable 10G long-distance links.
Q5: Why does single fiber damage cause full backhaul ring failure when using single-strand SFP+ BiDi 10G 40km module?
A: BiDi technology carries both uplink and downlink traffic on only one fiber strand, leaving no physical redundancy. HYTOPTODEVICE recommends customized network topology planning for SFP+ BiDi 10G 40km module deployment to avoid single-point fiber failure risks.
Q6: Why does minor fiber bending only degrade upstream traffic on 10G 40km BiDi module links?
A: 1330nm wavelengths are far more sensitive to macro-bend loss than 1270nm wavelengths, creating asymmetric signal attenuation. HYTOPTODEVICE SFP+ BiDi 10G 40km module adopts high-quality optical chips to reduce bending-induced unbalanced link degradation.
Q7: Why do 40km-rated BiDi optical modules trigger receiver overload errors on short 2km fiber testing links?
A: High-power 40km laser output oversaturates short-distance receivers without attenuation. HYTOPTODEVICE provides professional deployment guidelines for SFP+ BiDi 10G 40km module, suggesting inline attenuators for short-loop testing to prevent receiver damage.
Q8: What causes switch internal crosstalk interference with low-cost generic 10G 40km BiDi modules?
A: Cheap modules use low-isolation diplexers that cause internal TX laser leakage into RX channels. HYTOPTODEVICE SFP+ BiDi 10G 40km module applies premium high-isolation diplexer design to completely eliminate switch crosstalk and internal signal interference.
Q9: Why do network switches generate high heat after installing full-population 40km SFP+ BiDi 10G modules?
A: Long-reach 40km 10G BiDi modules require higher laser driving power, leading to greater thermal output. HYTOPTODEVICE optimizes internal circuit and heat dissipation structure for its SFP+ BiDi 10G 40km module, lowering operating temperature for dense rack deployment.
Q10: Why standard OTDR tools cannot locate fiber breaks on live operating SFP+ BiDi 10G 40km module links?
A: Traditional OTDR test signals conflict with active BiDi working wavelengths and disrupt live traffic. HYTOPTODEVICE provides dedicated wavelength-selective testing solutions for live SFP+ BiDi 10G 40km module links to support safe and accurate fiber fault detection.
Packaging & Custom OEM Solutions
Each module is individually sealed in ESD-safe anti-static packaging and ready for immediate shipment. For high-volume distributors, wholesalers, and system integrators, we offer flexible OEM programs—including custom logos, private labeling, and branded packaging—to help you build and protect your own brand.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

Others


