Huawei SFP-10G-BXD1 Compatible SFP+ 10G BiDi Transceiver 10GBASE-BX-D (SMF, 1330nm-TX/1270nm-RX, 10km, Simplex LC, DDM)
Product Overview
This Huawei SFP-10G-BXD1 Compatible SFP+ 10G BiDi transceiver is 10GBASE-LX 10km OS2 SMF commercial indoor BiDi transceiver, a direct drop-in replacement for Huawei OEM optics. It delivers stable 10GBASE-BX transmission up to 10km over OS2 single-mode fiber with 1330nm-TX/1270nm-RX simplex LC interface.The compatible SFP+ 10G BiDi Transceivers always operate in pairs with matching complementary wavelengths. Compliant with Hot Pluggable SFP+ MSA, SFF-8472, IEEE 802.3ae and RoHS standards, Featuring real-time DDM monitoring, low power consumption and high speed, the MSA compliant SFP+ 10G BiDi Transceiver is ideal for enterprise campus inter-building uplinks, metro ISP fiber backhaul, remote office interconnection and small datacenter inter-switch uplinks,.etc. We support samples, bulk wholesale and OEM private labeling, submit bulk inquiry or RFQ for competitive pricing and long-term supply contracts.
Key Technical Specifications
| Huawei Compatible |
SFP-10G-BXD1 |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP+ |
Max Data Rate |
10.7Gbps |
| Wavelength |
TX1330nm/RX1270nm |
Max Distance |
10km |
| Connector |
Simplex LC |
Transmitter Type |
1330nm DFB |
| Cable Type |
SMF |
Receiver Type |
PIN |
| TX Power |
-5.0~0dBm |
Receiver Sensitivity |
< -14.4dBm |
| Max. Power Consumption |
≤1W |
DOM/DDM |
Fully Supported |
| Protocols & Standards |
SFP+ MSA, SFF-8472, IEEE 802.3ae, RoHS Compliant |
Operation Temperature |
0 to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Operational Best Practices
• BiDi Pairing Rule: SFP‑10G‑BXD (Tx1330/Rx1270) must pair with
SFP‑10G‑BXU (Tx1270/Rx1330) at remote end. Two BXD modules will NOT form a valid link.
• Cabling Requirement: Use OS2 single‑mode simplex‑LC UPC cables only. Multimode fiber / APC connectors reduce reach and cause link issues; keep connectors clean.
• Port Notice: Install only into standard SFP+ ports. Do not force into 1G‑SFP slots. Disable transceiver‑block policy if needed on host devices.
• Environment: Run within 0‑70 °C. Avoid high‑heat, dusty, poorly ventilated rack positions.
• Hot‑swap: Supports hot‑swap; disconnect fiber before plugging / unplugging to protect optical ports.
• DDM Monitoring: Enable DDM/DOM; monitor optical power and temperature for early fault warning.
• Pre‑test Recommendation: Test sample units with real hardware before large‑scale bulk deployment.
• Laser Safety: Avoid direct eye exposure to powered optical ports; infrared laser can harm eyes.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Network Hardware
1.Huawei Native Compatibility
This HYTOPTODEVICE SFP+ 10G BiDi Transceiver achieves automatic alarm-free plug-and-play identification on all Huawei VRP switches supporting SFP-10G-BXD1. No manual configuration adjustments are needed, and full DDM DOM monitoring functions work natively after insertion.
- Huawei CloudEngine Data Center Switches: CE5800, CE6800, CE7800, CE8800 Series
- Huawei Campus Access/Aggregation Switches: S5735, S6735, S5720, S6720 Series
- Huawei MSR Integrated Service Routers: MSR3600, MSR5600, MSR3300 Series
- Huawei Fiber Access OLT & ONU Platforms: MA5600, MA5800 Series
2.Multi-Brand Cross Compatibility
This HYTOPTODEVICE SFP+ 10G BiDi Transceiver maintains stable interoperability for mixed-vendor indoor network architectures, suitable for campus renovation, central office ISP construction and system integration turnkey projects.
Supported brands include Cisco, Huawei, Juniper Networks, Arista, HPE, H3C and other mainstream brands
Primary Application Scenarios
• Single‑Fiber Enterprise Access Networking: 10km point‑to‑point links saving fiber resources for campus building‑to‑building interconnection
• Metro Aggregation & FTTO Deployment: Cost‑effective 10G single‑fiber links for enterprise FTTO and carrier access network construction
• Data‑Center Short‑Reach Single‑Fiber Interconnect: Space‑saving BiDi connections within and adjacent data‑center sites up to 10km
• Cost‑Effective Hardware Upgrade: Direct drop‑in replacement for expensive original Huawei SFP‑10G‑BXD1 modules to reduce 10G network procurement costs for bulk purchase
• OEM Wholesale Resale: Stable bulk supply for global optical transceiver distributors and network equipment vendors for private label resale business
Connectivity Solutions(Applications)
1.10G Switch-to-Switch Interconnection

2.10G Switch-to-NIC Direct Connection

3.10G Structured Cabling Rack Layout

The Core Features
1.50% Fiber Resource Saving & Low-Cost Network Upgrade
Optimize your current network infrastructure without the high cost of laying new cables. By transmitting and receiving signals over a single strand of fiber, our 10G BiDi SFP+ transceivers help you squeeze maximum value out of your existing fiber cabling.

2.Double Your Network Capacity Instantly
Upgrade your bandwidth effortlessly. Utilizing advanced Wavelength Division Multiplexing (WDM) technology, this module allows bidirectional traffic over a single fiber strand, effectively doubling your network capacity instantly while cutting cabling costs in half.

3.Energy-Efficient 10G Connectivity for Data Centers
Designed for high-density, high-speed modern data centers, this SFP+ transceiver features an ultra-low power consumption of just 1W. Achieve stable, green, and cost-effective 10G data transmission while significantly reducing operational cooling costs.

4.Seamless Cross-Brand Interoperability
Enjoy worry-free integration into your multi-vendor environment. Every single unit undergoes rigorous compatibility testing on original brand switches to ensure seamless cross-brand interoperability. Real products, real switches, real results—Specific Compatibility Video available upon request.

5.Comprehensive Testing for Rock-Solid Reliability
Reliability is our cornerstone. From signal integrity and distance runs to extreme temperature cycles, our comprehensive testing procedure guarantees that every 10G BiDi 10km SFP+ module delivers stable, packet-loss-free performance under any network load before leaving our Test Center.

FAQ
Q1: Do HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM modules need vendor-locked firmware updates to keep compatible after switch OS upgrade?
A: No, HYTOPTODEVICE premium SFP+ 10G BIDI TRANSCEIVER 10KM requires no vendor-locked firmware updates at all. Our modules adopt universal compatible coding design, which can maintain stable and full compatibility permanently even after switch system OS upgrades, avoiding link failure and compatibility bugs caused by firmware update restrictions.
Q2: How to fix reception errors and port flapping issues caused by third-party compatibility mismatch for HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM?
A: For third-party compatibility mismatch problems triggering reception errors and port flapping, the HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM supports quick troubleshooting solutions. You can clean fiber end faces, reinsert the transceiver firmly, fix the 10G port speed negotiation mode, and our pre-programmed universal compatibility code can perfectly eliminate mismatch failures, realizing stable link operation.
Q3: How to identify the TX and RX wavelengths via physical label and pull-tab color of HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM?
A: The HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM adopts a humanized identification design. Users can quickly distinguish accurate TX and RX wavelengths through the customized pull-tab color of the module, and all standard wavelength parameters are clearly marked on the physical label of the product, realizing zero-cost and fast wavelength matching.
Q4: Is it available to pair HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM with 10G BiDi 20KM modules with consistent wavelengths?
A: It is not recommended to cross-match them. Although the wavelengths are consistent, the HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM is professionally calibrated for 10KM optical power budget and attenuation parameters. Matching with 20KM BiDi modules will cause mismatched optical power, resulting in unstable network links and abnormal signal transmission.
Q5: Why do HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM have high BER when transmitting over 9.5km fiber length?
A: The high bit error rate (BER) at 9.5km fiber span is caused by marginal optical power margin. The HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM supports standard 0-10KM stable transmission range. Near the limit distance of 9.5km, slight fiber attenuation and signal loss will lead to increased BER, which is a normal optical transmission characteristic of 10KM-level transceivers.
Q6: Why do HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM cause one-way random packet drops with normal download and abnormal upload?
A: The one-way directional packet drop issue stems from unbalanced bidirectional optical signal transmission. The HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM features precise unidirectional power calibration. If the paired module has inconsistent transmit power, it will cause upload signal attenuation and random packet drops, while the download signal channel remains intact and stable.
Q7: Does HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM support SyncE and IEEE 1588 PTP precise timing protocols?
A: Yes, the high-performance HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM fully supports Synchronous Ethernet (SyncE) and IEEE 1588 PTP precise timing protocols. It can meet the high-precision timing requirements of industrial communication, data center and smart network scenarios, with stable timing synchronization and low delay.
Q8: Does the purchase price of HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM include on-site custom programming coding tools?
A: The official quotation of standard HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM does not include custom programming coding boxes and on-site programming tools. Our modules are pre-programmed with universal compatible firmware before delivery, and professional coding tools can be provided as optional supporting accessories according to customer needs.
Q9: Can HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM seamlessly support standard 10GBASE-BX10 Ethernet protocol?
A: Absolutely yes. The HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM is strictly designed and tested in accordance with the 10GBASE-BX10 industry standard protocol. It can seamlessly adapt to all standard 10G Ethernet switching devices, realizing plug-and-play and stable protocol compatibility without link adaptation failures.
Q10: Can HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM be used in government and financial sensitive supply chain security networks?
A: Yes. The HYTOPTODEVICE SFP+ 10G BIDI TRANSCEIVER 10KM adopts standardized supply chain production and strict quality control procedures, with compliant and traceable product sources. It fully meets the strict supply chain security policies of government, finance and other sensitive industries, and can be safely deployed in high-security-level network environments.
Packaging & Custom OEM Solutions
Each module ships individually sealed in ESD-safe packaging, protected from static from our warehouse to your shelf—and ready to ship on receipt of order. Volume buyers and system integrators also unlock our full OEM program: custom logos, private labeling, and branded packaging, all designed to help you build and protect your own brand.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- Up to 70% cost savings vs OEM, transparent pricing & flexible bulk rates, supported quality returns
- 100% real-device compatible with Cisco, Huawei,Dell,Juniper, and Arista
- ISO 9001:2015 Shenzhen factory, full lineup: 1.25G/10G/25G/40G/100G/200G/400G/800G/1.6T transceivers
- Ample stock, fast global DHL/FedEx shipping in 3–5 working days
- Free pre-sales engineering support for custom EEPROM & private label firmware
- Real switch test videos available for pre-purchase review; inspection & shipping videos provided per order
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration

Others


