HPE ProCurve J4858C Compatible 1000BASE-SX Pluggable Transceiver | SFP 850nm 550m MMF Bulk & Wholesale | HYTOPTODEVICE
Product Overview
This HYTOPTODEVICE 1000BASE-SX pluggable transceiver is fully compatible with HPE ProCurve J4858C. It meets IEEE 802.3z and SFF-8472 industry standards, delivering stable 1.25Gbps gigabit transmission.
Preloaded with official HPE EEPROM firmware, this pluggable transceiver supports zero-alarm plug-and-play. It works seamlessly with HPE ProCurve and Aruba switches, serving as a perfect low-cost replacement for OEM J4858C modules.
Built with high-quality 850nm VCSEL laser, it supports 550m transmission on OM2/OM3/OM4 fiber and 275m on legacy OM1 fiber. Built-in DDM monitoring enables real-time status tracking. Every pluggable transceiver passes strict aging and real-switch testing, stable for 7×24 operation and large-scale bulk deployment.
Key Technical Specifications
| HPE ProCurve Compatible |
J4858C |
Vendor Name |
HYTOPTODEVICE |
| Form Factor |
SFP |
Max Data Rate |
1.25Gbps |
| Wavelength |
850nm |
Max Distance |
550m over OM2 MMF |
| Connector |
Duplex LC |
Transmitter Type |
850nm VCSEL |
| Cable Type |
MMF |
Receiver Type |
PIN |
| TX Power |
-9.0~-3dBm |
Receiver Sensitivity |
< -18.0dBm |
| Typical Power Consumption |
≤0.8W |
Receiver Overload |
-3dBm |
| Bit Error Ratio (BER) |
1E-12 |
DDM/DOM |
Supported |
| Protocols |
SFF-8472 MSA Compliant, IEEE 802.3ah-2004 |
Operation Temperature |
0°C to 70°C (32 to 158°F) |
Usage Guidelines & Best Practices
-
Fiber Choice: Duplex LC OM1/OM2/OM3/OM4 MMF (50 or 62.5/125 µm). Do NOT use SMF (OS1/OS2).
-
Connector Match: UPC/PC polish only. Do NOT use APC.
-
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
-
Link Setup:Lock speed to 1.25Gbps (Full Duplex) manually if auto-negotiation fails.
-
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
-
Installation & Hot-Swap Rules:MSA hot-swappable. Insert/remove gently without powering down.
-
Environment:Commercial grade (0°C to 70°C). Avoid extreme heat, moisture, and dust.
Links to the Datasheet, User Guide and Compatibility Guides are available on the product page.
Full Compatibility List and Supported Devices
1. Supported Hardware & Firmware
This HYTOPTODEVICE pluggable transceiver is pre-flashed with official HPE firmware for zero-alarm plug-and-play and hot-swap support. It serves as a perfect drop-in replacement for original HPE ProCurve J4858C modules with no manual configuration required. It is fully compatible with the following mainstream HPE and Aruba switch models:
-
HPE ProCurve 2300 Series: 2312, 2324
-
HPE ProCurve 2500 Series: 2512, 2524
-
HPE ProCurve 2510 Series: 2510-24, 2510-48, 2510G-24, 2510G-48
-
HPE ProCurve 2800 Series: 2824, 2848
-
HPE ProCurve 3400cl Series: 3400cl-24G, 3400cl-48G
-
HPE Aruba Gigabit Switches: 1900, 2500, 2900, 3500 enterprise switch platforms
2. Multi-Brand Cross Compatibility
This 1000BASE-SX pluggable transceiver strictly follows MSA unified standards, enabling stable interoperability with Cisco, Juniper, Brocade, Ubiquiti and other third-party gigabit network devices. Custom EEPROM firmware coding is available to adapt to mixed-vendor network environments, meeting diverse enterprise networking construction needs.
3. Free Value-Added Services
-
Custom firmware for multi-device compatibility
-
Free sample testing before bulk orders
-
Complete test reports for project acceptance
-
Strict batch consistency quality control
- Free custom EEPROM programming for special and legacy network environments
Main Application Scenarios
HYTOPTODEVICE HPE ProCurve J4858C pluggable transceiver is widely used in various short-range gigabit multimode fiber networking scenarios:
-
Enterprise Office LAN Uplinks: Gigabit uplink connection of HPE access switches in office buildings.
-
Data Center Intra-Rack Connections: Short-distance interconnection between servers, top-of-rack switches and HPE core switches.
-
Legacy HPE Network Upgrade: Cost-effective replacement for aging original J4858C modules to renew old gigabit network systems.
-
Campus & Park Network Construction: Short-range multimode fiber networking for campus building internal and cross-room connections.
Connectivity Solutions(Applications)
1.1GbE Switch-to-Switch Connectivity

2.1GbE Switch to Media Converter Connectivity
3.1GbE Structured Cabling Interconnect

4.1GbE Switch-to-NIC Interconnection

The Core Feature
1. High-Efficiency 1G Data Center Interconnect
Engineered for high-density network environments, our SFP-1GE-SX modules deliver plug-and-play 1GbE performance with ultra-low power dissipation—offering a budget-friendly, eco-conscious solution for your daily networking needs.
2.Zero-Downtime Reliability & 100% Brand Compatibility
Rest assured with optical transceivers rigorously benchmarked on over
150+ major brand host switches in our testing lab. Verify your setup instantly via our compatibility sheet—or request a custom, switch-specific
Compatibility Video before you buy.
3.Lab-Certified Quality, Built for Zero Failures
Every transceiver is stress-tested on advanced optoelectronic diagnostics to guarantee signal integrity and long-term stability. Experience full transparency—take a virtual tour of our
Test Center to see our Quality Assurance process in action.

FAQ
Q1: How to fix switch “Unsupported Transceiver” error for third-party SFP modules?
A: This error occurs when the module’s EEPROM vendor code fails to match your switch brand. You can resolve it by enabling the switch’s unsupported transceiver command or requesting pre-recoded firmware for HYTOPTODEVICE HPE ProCurve J4858C pluggable transceiver to achieve seamless recognition.
Q2: Does HPE J4858C compatible pluggable transceiver support port auto-negotiation?
A: Auto-negotiation is fully supported. For maximum link stability in enterprise LAN deployment, manually locking the port to 1000Mbps Full-Duplex is recommended to avoid random speed and duplex mismatches.
Q3: What is the maximum working distance for 1000BASE-SX gigabit SFP pluggable transceiver?
A: This HPE J4858C pluggable transceiver delivers up to 550 meters stable transmission over OM2/OM3/OM4 multimode fiber, and 275 meters over traditional OM1 multimode fiber for indoor short-range networking.
Q4: What operating range can I get with standard OM1 62.5/125μm multimode fiber?
A: Due to modal dispersion limitations of legacy OM1 fiber, the maximum reliable transmission distance is capped at 275 meters when paired with 850nm 1000BASE-SX pluggable transceiver modules.
Q5: Is cross-connection possible between 850nm SX and 1310nm LX optical modules?
A: Interconnection between SX and LX modules is not feasible. Fiber link connections require matching wavelength and optical type at both ends to establish valid gigabit network links.
Q6: Is an optical attenuator required for short 1m to 5m multimode fiber jumper connections?
A: No additional attenuator is needed. Adopting 850nm VCSEL laser design, this pluggable transceiver features moderate optical output power and will not cause receiver saturation on short fiber links.
Q7: What is the official receiver sensitivity specification for J4858C pluggable transceiver?
A: The professional receiver sensitivity of this HPE-compatible pluggable transceiver is ≤ -18 dBm, ensuring stable signal reception and ultra-low bit error rate in standard multimode fiber environments.
Q8: What physical interface connector is equipped on HPE J4858C SFP pluggable transceiver?
A: This 1000BASE-SX pluggable transceiver adopts industry-standard Duplex LC UPC connector, universally compatible with mainstream enterprise multimode fiber patch cords and cabling systems.
Q9: Will incorrect TX/RX wire sequence affect SFP fiber link connectivity?
A: TX/RX polarity crossover connection is mandatory. The transmit end of one pluggable transceiver must connect to the receive end of the opposite module; incorrect wiring will result in link failure.
Q10: Is hot-swap function supported on HPE ProCurve J4858C pluggable transceiver?
A: Yes, the module supports full hot-swappable operation. It can be plugged or unplugged on active switches without device shutdown or network service interruption.
Q11: What is the reliability grade and MTBF lifespan of these gigabit SX SFP modules?
A: HYTOPTODEVICE industrial-quality pluggable transceiver boasts an MTBF of over 1,000,000 hours, supporting long-term 7×24 continuous operation for enterprise and data center networks.
Q12: Are third-party compatible SFPs trustworthy compared with original HPE OEM modules?
A: Absolutely reliable. Standard-compliant third-party pluggable transceivers adopt equivalent core laser and chip components as OEM modules, providing identical performance at lower bulk procurement cost.
Q13: Can commercial-grade SFP pluggable transceiver work in outdoor unconditioned cabinet environments?
A: Commercial modules are only suitable for indoor constant-temperature environments. Outdoor high/low temperature scenarios require customized industrial-grade pluggable transceivers with -40℃ to 85℃ working range.
Q14: Do HPE J4858C compatible pluggable transceivers meet international certification standards?
A: All modules are fully certified with RoHS, CE, FCC and REACH compliance, meeting global environmental protection and safety standards for commercial network deployment.
Q15: How does freezing low temperature impact commercial SFP transceiver operation?
A: Commercial-grade pluggable transceivers have a minimum working temperature of 0℃. Sub-zero freezing environments will trigger laser bias errors and cause unstable links or complete disconnection.
Packaging Options & Custom‑Packaging Solutions
Every transceiver module gets reliable ESD‑safe packaging out of the box. Standard packing is ready for immediate shipment, while custom‑printed packaging with your logo is available for bulk orders.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
- 100% MSA-compliant modules with Cisco, Huawei,Dell,Juniper, and Arista compatibility
- ISO 9001:2015 certified manufacturing facility in Shenzhen
- Average lead time of 3–5 business days with DHL/FedEx express options
- Dedicated pre-sales engineering support for custom configurations
- Actual hardware,actual switches,actual results.we publish compatibility test video,eliminate compatibility anxiety. you can watch before you buy.
- We can provide inspection and shipping videos to make you feel as if you are right here with the product.
"We replaced 200 Cisco-branded SFPs with HYTOPTODEVICE equivalents across our spine layer — zero compatibility issues, 40% cost reduction."— Network Architect, Tier-2 ISP, Germany
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final inspection, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
-
ISO 9001: Certified quality management and production consistency.
-
CE & FCC: Fully compliant for seamless Global Market Access.
-
RoHS: Committed to environmental responsibility and hazardous material control.
-
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.

Rigorous Industrial Product Testing

100% 3rd Party Compatible

Partial Test Demonstration
