| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-200G-SR4-S | QSFP56-200G-FR4 |
| 2 | Arista | QSFP-200G-SR4 | QSFP56-200G-LR4 |
| 3 | Dell | Q56-200G-SR4 | QSFP56-200G-ER4 |
| 4 | Huawei | QSFP56-200G-SR4 | |
| 5 | Ruijie Networks | 200G-Q56-SR4-MM850 | |
| 6 | NVIDIA/Mellanox | MMA1T00-VS | |
| 7 | H3C | QSFP56-200G-SR4-MM850 |
Cisco Compatible |
QSFP-200G-SR4-S | Vendor Name | HYTOPTODEVICE |
| Form Factor | QSFP56 | Max Data Rate | 200Gbps (4x50Gbps) |
| Wavelength | 850nm
|
Max Distance | 70m on OM3/100m on OM4 |
| Modulation Format | PAM4 | Host Required | FEC |
| Connector | MPO-12(UPC) | Voltage Supply | 3.3V |
| Cable Type | MMF | Receiver Overload | 4dBm |
| Transmitter Type | VCSEL 850nm | Receiver Type | PIN |
| TX Power | -6.5~+4.0dBm | Receiver Sensitivity | < -8.4dBm |
| Operation Temperature | 0 to 70°C (32 to 158°F) | Maximum Power | < 4.5W |
| Protocols | QSFP56 MSA, IEEE 802.3bs | Application | 200G Ethernet, High performance computing, Data Center Interconnect |
Usage Guidelines & Best Practices
Fiber Choice: Only works with OM3 / OM4 multi‑mode MPO‑12 trunk cable; single‑mode fiber cannot support 850nm SR4 transmission and will lead to link failure.
Distance Limit: Max 70m on OM3 MMF, max 100m on OM4 MMF; excessive splices, dirty end‑faces or sharp bends reduce actual working distance.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Installation Specification: Hot‑plug supported; keep MPO connector end‑faces clean, observe minimum fiber‑bend radius requirements.
Operating Environment: Commercial temperature range 0°C‑70°C; maintain cabinet airflow to avoid module overheating.
For detailed operation instructions, please refer to the User Guide.
This module adopts Cisco‑specific EEPROM, supporting zero‑alarm plug‑and‑play with official firmware. All products are strictly temperature burn‑in tested before shipment, fully compatible with the below Cisco hardware models:
Cisco Nexus Data Center Switches: Nexus 9300‑FX3 Series, Nexus 9364E Series, Nexus 9200 Series
Cisco UCS Series: UCS 5108 blade chassis with QSFP56 capable I/O modules
Universal Compatibility: All Cisco devices with standard QSFP56 ports supporting 200GBASE‑SR4 protocol. Breakout functions rely on switch firmware support.
Built on universal MSA open standards, this QSFP56 transceiver is interoperable with mainstream network brands including Arista, Juniper, H3C, Huawei and Fortinet, adapting to mixed‑vendor leaf‑spine network upgrade and expansion scenarios.
• Leaf‑spine fabric deployments for modern AI‑ready data‑center architectures
• High‑density rack‑to‑rack trunk interconnections
• 200G high‑speed server and storage uplink connections
• 200G to 2×100G / 4×50G breakout architecture (host‑firmware dependent)
• Cost‑effective Cisco data‑center network hardware upgrade projects
• Inventory supply for global distributors and system integrators for data‑center tender projects







Q2: Can I insert this 200G SR4 module into a Cisco 400G QSFP-DD port?
A: Yes. Cisco's 400G QSFP-DD ports are backward-compatible. A QSFP56 module can physically and electrically map into the lower-speed lane configurations of a QSFP-DD slot and will run natively at 200G.
Q3: What type of fiber optic patch cord is used for this 200G SR4 transceiver?
A: It uses a Multi-Mode Fiber (MMF) patch cable with an MPO-12 (UPC) connector. the dual-LC fibers can not be used.
Unsupported Cable) and disable the port to protect signal integrity.Q10: Can this 200G QSFP56 SR4 optic physically fit into legacy QSFP28 network device slots?
A: No. QSFP56 is a distinct form‑factor and cannot plug into QSFP28 ports. This Cisco‑compatible 200GBASE‑SR4 transceiver requires native QSFP56 ports to achieve full 200G PAM4 throughput.
Q11: What pre‑condition is needed for this module to run on non‑Cisco multi‑vendor network equipment?
A: Matching vendor‑specific EEPROM signature must be pre‑loaded. When placing bulk orders, integrators should notify HYTOPTODEVICE sales of target hardware brands to get correct pre‑coded units.
Q12: Which fiber grade determines whether I can achieve the maximum 100‑meter transmission distance?
A: OM4 multi‑mode fiber is required for full 100‑meter reach; OM3 MMF limits valid links to maximum 70 meters. Our engineering team can review your existing cabling plant during pre‑sales planning.
Q13: Are all Cisco QSFP56 switches capable of enabling 2×100G SR2 breakout with this 200G SR4 module?
A: Breakout modes of 2×100G SR2 or 4×50G SR are hardware‑supported on the module side, but the feature depends entirely on host switch firmware capability. Please validate firmware compatibility during PoC testing before large‑scale deployment.
Q14: What resources and after‑sales assistance are offered for bulk buyers needing on‑site EEPROM reprogramming?
A: You will need an optical transceiver programming coding box and matching software to rewrite the module's compatibility profile. HYTOPTODEVICE supplies both coding box and software for bulk buyers to re‑program modules on‑site, paired with lifetime free technical support for this 200G QSFP56 SR4 transceiver.
Q15: Why is host‑activated FEC mandatory for reliable 200GBASE‑SR4 PAM4 links?
A: PAM4 modulation has inherently lower signal‑to‑noise tolerance compared to NRZ signaling. Host‑side FEC corrects lane‑level bit‑errors caused by multi‑mode modal noise, and must be turned on to avoid intermittent packet loss.
Q16: Can operators read real‑time optical performance metrics from this 200G QSFP56 SR4 module remotely?
A: Yes, CMIS‑based DDM/DOM monitoring is fully supported. Network administrators can remotely observe module temperature, supply voltage, laser bias, transmit and receive power for routine link health auditing.
Q17: What differentiates SR4 optics from other 200G QSFP56 transceiver variants such as DR4 or FR4?
A: SR4 is a parallel multi‑mode short‑reach solution optimized for intra‑data‑center rack‑to‑rack connections. DR4 / FR4 utilize single‑mode fiber and target much longer campus‑scale inter‑building distances.
Q18: Are these bulk‑order 200G QSFP56 SR4 optical modules compliant for international data‑center deployments?
A: Yes, all HYTOPTODEVICE 200G QSFP56 SR4 transceivers comply with RoHS requirements. Complete compliance documentation can be provided for customs clearance and international project audits.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every module is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.




