| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-4SFP25-CU3M | |
| 2 | Arista Networks | CAB-Q28-S28-3M | |
| 3 | Brocade | 100G-Q28-S28-C-0301 | |
| 4 | Huawei | QSFP-4SFP25G-CU3M | |
| 5 | Juniper | QFX-Q-S-DAC-3M | |
| 6 | Dell | DAC-Q28-4SFP28-25G-3M |
| Juniper Compatible |
QFX-Q-S-DAC-3M
|
Vendor Name | HYTOPTODEVICE |
| Connector | QSFP28+ to 4 x SFP28 | Max Data Rate | 100Gbps |
| Cable Length | 3m (10ft) | Wire AWG | AWG 26 |
| Cable Type | Passive Twinax | Power Consumption | ≤0.25W |
| Media | Copper | Operation Temperature | 0~ 70 °C (32 to 158°F) |
| Jacket Material | PVC(OFNR) | Protocols | IEEE 802.3, QSFP28 MSA, SFF-8665 |
| Minimum Bend Radius | 50mm | Application | 100G to 2x 25G Ethernet, Data Centers |
Usage Guidelines & Best Practices
Mandatory Port Breakout Configuration: Ensure the host QSFP28 port supports channelization. Enable breakout mode (4x25G) via the switch CLI before connecting the cable.
Cabling Requirements: Do not exceed the minimum 50mm bend radius, avoid sharp folding, heavy extrusion or long-term tension on the cable assembly.
Port Installation Standard: Do not mix this breakout DAC with straight QSFP28 to QSFP28 DAC configuration.
Hot‑swap rule:Never pull or tug directly on the individual breakout legs. Always use the integrated pull-tab or bale latch when inserting or removing connectors.
Operating Environment: 0‑70℃, indoor cabinet deployment only.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
Built on universal MSA open standards, this 100G QSFP28 to 4 x 25G SFP28 passive DAC breakout cable can interoperate with mainstream network brands including Arista, Intel, Juniper, Dell, NVIDIA Mellanox and IBM, for mixed-vendor rack stacking and server fabric expansion.





Q1: Will this 100G breakout cable work with my Cisco switches and Juniper gear? A1: It is pre-validated for Juniper QFX platforms and interoperable with Cisco gear that enables breakout mode. HYTOPTODEVICE custom programs this passive direct attach copper breakout cable’s EEPROM to clear transceiver alarms in multi-vendor fabric setups.
Q2: Is this cable compatible with both QSFP28 and QSFP+ ports? A2: This passive direct attach copper breakout cable only fits QSFP28 interfaces. QSFP+ pinout and electrical characteristics differ, so stable communication cannot be established.
Q3: Can I use this cable to connect a 100G switch to four separate 10G switches? A3: This breakout cable runs 25G per lane, it requires SFP28 25G ports on the far end. It cannot negotiate down to 10G speed to link to 10G switch ports.
Q4: Do I need to buy specific brand-coded versions (e.g., Cisco-coded vs. HP-coded)? A4: Brand-specific coding is necessary for switches with vendor lock. HYTOPTODEVICE preloads matching firmware signatures into this passive direct attach copper breakout cable to avoid unsupported transceiver pop-ups.
Q5: Can I mix and match different brands of network cards on the SFP28 ends? A5: Cross-brand SFP28 NIC mixing is allowed if all adapters follow MSA 25GBASE-CR specs. HYTOPTODEVICE runs compatibility tests to guarantee consistent performance of this passive direct attach copper breakout cable.
Q6: What is the maximum supported data rate per channel? A6: Each individual channel runs at a fixed 25Gbps. This passive direct attach copper breakout cable divides one 100G QSFP28 port into four independent 25G data paths.
Q7: What is the maximum recommended cable length for passive copper twinax? A7: The reliable operating limit for this passive 25G twinax design is 5 meters. HYTOPTODEVICE supplies passive direct attach copper breakout cable in 0.5m, 1m, 3m and 5m standard lengths.
Q8: What is the typical latency of a copper twinax breakout cable? A8: Copper twinax latency averages roughly 0.6 ns per meter. This passive direct attach copper breakout cable has no signal processing chip, which suits low-latency Juniper HPC and AI networking.
Q9: What wire gauge (AWG) is used in this cable, and does it affect flexibility? A9: Common gauges range from 26AWG to 30AWG. Thinner gauges such as 30AWG deliver better flexibility for dense cable management, while 26AWG supports runs up to 3 meters, and 24AWG is required for stable 5-meter passive links. HYTOPTODEVICE supplies the correct AWG for every passive direct attach copper breakout cable length you order.
Q10: Does this cable support auto-negotiation? A10: 25GBASE-CR passive twinax does not support auto-negotiation. You have to manually lock both link ends to 25G fixed speed when deploying this HYTOPTODEVICE breakout cable.
Q11: How flexible is the cable? Can I bend it tightly inside a crowded rack? A11: It offers moderate flexibility for rack routing, yet sharp tight bends are prohibited. Stick to the 55mm minimum bend radius rule to prevent internal conductor damage to this passive direct attach copper breakout cable.
Q12: Are the SFP28 ends labeled clearly to show which channel is which (Lane 1 to 4)? A12: Yes, each SFP28 pigtail carries permanent laser marking for Lane 1 to Lane 4. HYTOPTODEVICE marks every breakout tail of this passive direct attach copper breakout cable to simplify cabling documentation.
Q13: Can I route this cable between different server racks? A13: It works for short inter-rack connections within its 3-meter total span. This passive direct attach copper breakout cable is designed for adjacent rack links instead of long-distance cabling across the data hall.
Q14: What color options are available for the cable jacket? A14: Black jacket is our standard offering. HYTOPTODEVICE can manufacture custom jacket colors on bulk orders of this passive direct attach copper breakout cable for your rack labeling scheme.
Q15: Can I get a custom length (e.g., 2.5 meters) instead of standard sizes? A15: Non-standard custom lengths are available for bulk orders. Reach out to HYTOPTODEVICE sales team for pricing and lead time of custom-length passive direct attach copper breakout cable.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.




