| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-100G-CU2M | |
| 2 | Arista Networks | CAB-Q-Q-100G-2M | |
| 3 | Juniper | QFX-QSFP28-DAC-2M | |
| 4 | Brocade | 100G-Q28-Q28-C-0201 | |
| 5 | Dell | DAC-Q28-100G-2M | |
| 6 | Huawei | QSFP28-100G-CU2M |
| Huawei Compatible |
QSFP28-100G-CU2M
|
Vendor Name | HYTOPTODEVICE |
| Connector | QSFP28 to QSFP28 | Max Data Rate | 100Gbps |
| Cable Length | 2m (7ft) | Wire AWG | AWG 30 |
| Cable Type | Passive Twinax | Power Consumption | ≤0.5W |
| Media | Copper | Operation Temperature | 0~ 70 °C (32 to 158°F) |
| Jacket Material | PVC(OFNR) | Protocols | QSFP28 MSA, SFF-8662, IEEE 802.3 |
| Minimum Bend Radius | 35mm | Application | 100 Gigabit Ethernet |
Usage Guidelines & Best Practices
Mandatory Port Setting: Host QSFP28 port must enable 100GBASE-CR4 mode; link negotiation failure will happen if forced to optical mode.
Cabling Requirements: Do not exceed the minimum 35mm bend radius, avoid sharp folding, heavy extrusion or long-term tension on the cable assembly.
Port Installation Standard: Works only with standard QSFP28 100G ports; cannot be inserted into SFP+ or XFP slots. Disable the host’s third-party transceiver lock policy in advance if required.
Maintenance Specification: Hot‑swap supported, grip the pull tab instead of pulling the cable body during plug/unplug to prevent internal conductor damage.
Operating Environment: This commercial-grade cable operates reliably within 0℃‑70℃; avoid installation beside high-heat power modules.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
Built on universal MSA open standards, this 100G QSFP28 passive copper twinax cable can interoperate with mainstream network brands including Arista, H3C, Juniper, Dell, NVIDIA Mellanox and more, for mixed-vendor rack stacking and server fabric expansion.







Q1: What is the maximum reliable operating length for standard passive direct attach copper cable at 100G? A: Standard passive direct attach copper cable follows MSA rules with a maximum reliable reach of 5 meters for 100GBASE-CR4. Beyond this distance, 25G per-lane signal loss exceeds receiver sensitivity limits. HYTOPTODEVICE passive direct attach copper cable lineup covers all standard lengths up to 5m; longer connections require active retimer DAC or fiber AOC.
Q2: Why does high-frequency signal attenuation get worse as passive direct attach copper cable length increases? A: Skin effect and dielectric loss grow sharply at 25G serial frequencies, which weakens signals on longer copper twinax. More length reduces the signal eye margin and lowers transmission stability. HYTOPTODEVICE passive direct attach copper cable adopts low-loss twinax material to keep attenuation within acceptable limits for its rated length.
Q3: Can I deploy passive direct attach copper cable for inter-rack cabling inside a data center? A: Passive direct attach copper cable is not suitable for most inter-rack deployments. They only work for adjacent racks or top-of-rack (ToR) to end-of-row (EoR) switches within close proximity (under 5 meters). Longer inter-rack runs often exceed the 5m passive DAC limit and bring extra crosstalk and EMI risk. HYTOPTODEVICE recommends AOC or fiber transceivers for cross-room or long-distance inter-rack data center connections.
Q4: Why do infrastructure engineers pick AOC over passive direct attach copper cable for links longer than 5 meters? A: Active optical cables break the copper attenuation limit and maintain stable connections over extended distances. Optical signals are immune to EMI and crosstalk, unlike copper twinax. HYTOPTODEVICE supplies both passive direct attach copper cable and matching AOC products to meet different reach requirements.
Q5: How does changing rack ambient temperature affect the usable signal reach of passive direct attach copper cable? A: Higher temperature raises copper resistance and amplifies signal attenuation, shrinking the available link margin. HYTOPTODEVICE passive direct attach copper cable passes thermal cycle testing from 0°C to 70°C to guarantee stable performance under typical data center thermal conditions.
Q6: What problems will occur when the EEPROM of a passive direct attach copper cable is mismatched with my Huawei switch? A: Incorrect EEPROM coding triggers unsupported transceiver alerts and may block link negotiation. Most enterprise switches verify vendor signature at startup. Every HYTOPTODEVICE passive direct attach copper cable is pre-coded and validated for Huawei VRP and other target platforms to avoid handshake failures.
Q7: Can one passive direct attach copper cable carry separate vendor EEPROM profiles on each end, such as Huawei on one side and another brand on the other? A: Our standard passive direct attach copper cable does not support dual dissimilar vendor coding on two ends. A unified vendor signature is required for stable port handshake. Contact the HYTOPTODEVICE sales team to discuss custom EEPROM engineering for special mixed-vendor fabric projects.
Q8: Does passive direct attach copper cable support vendor-exclusive telemetry and DOM monitoring on Huawei switches? A: Passive direct attach copper cable only supports basic MSA DOM readouts; proprietary vendor telemetry functions are unavailable. This copper assembly contains no optical laser or receiver chips. HYTOPTODEVICE preloads standard MSA DOM data so your Huawei VRP switch can read cable ID and baseline diagnostic information.
Q9: Is there a measurable latency gap between passive direct attach copper cable and fiber patch cords? A: Passive direct attach copper cable delivers slightly lower latency than fiber links. Electrical signals travel faster in copper than light in glass fiber, with the typical difference below 1 nanosecond. Low-latency HYTOPTODEVICE passive direct attach copper cable fits AI, HPC and low-latency leaf-spine deployments.
Q10: Can passive direct attach copper cable pick up EMI noise in high-density data center racks? A: Copper twinax is more susceptible to EMI than fiber, but full shielding can greatly suppress interference. Poor routing near high-current power cables may still introduce noise. HYTOPTODEVICE passive direct attach copper cable uses full shielded construction to meet global EMI compliance standards.
Q11: What symptoms show signal degradation on passive direct attach copper cable, and will it drop links instantly? A: Gradual signal degradation normally creates rising CRC error counters before full link loss. A shrinking signal eye window causes random bit flips that register as CRC faults. If CRC errors appear, confirm your HYTOPTODEVICE passive direct attach copper cable is used within rated length and bend specifications.
Q12: Will tight bending inside cable managers permanently damage the conductors inside passive direct attach copper cable? A: Bending below the minimum bend radius will deform internal twinax conductors and permanently hurt signal quality. This cable requires a minimum bend radius equal to 5 times its outer diameter. Careful routing protects your HYTOPTODEVICE passive direct attach copper cable from hidden mechanical damage and bit errors.
Q13: Can thick bundles of passive direct attach copper cable block airflow and cause thermal overheating for network hardware? A: Dense, tightly bundled copper cables can block front-to-back rack airflow and raise component temperatures. Copper retains more heat than thin fiber cabling. HYTOPTODEVICE uses slim 30AWG wire for passive direct attach copper cable to reduce bulk and preserve airflow in dense racks.
Q14: Do the connector shells of passive direct attach copper cable provide proper thermal dissipation? A: Passive direct attach copper cable has almost no active electronics inside connectors and generates negligible heat. Most heat comes from the host switch ASIC port, not the cable itself. HYTOPTODEVICE connector housings adopt thermally optimized plastic to support normal port cooling.
Q15: In which scenarios should I choose passive direct attach copper cable instead of 100G AOC? A: Select passive direct attach copper cable for short intra-rack runs under 5m to cut power consumption and deployment cost. It operates at zero power and simplifies installation work. HYTOPTODEVICE passive direct attach copper cable is the cost-effective option for short leaf-spine connections within a single rack.
Q16: What are the power consumption differences among passive direct attach copper cable, active DAC and optical transceiver links? A: Passive direct attach copper cable consumes 0W. Active retimer DAC draws roughly 1–2W per end, while a pair of optical transceivers usually consumes 3–6W total. Zero-power HYTOPTODEVICE passive direct attach copper cable reduces rack power load and lowers overall data center TCO.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.




