| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | XFP-10G-MM-SR | |
| 2 | Dell | 320-5164 | |
| 3 | H3C | XFP-SX-MM850 | |
| 4 | HPE BladeSystem | 443756-B21 | |
| 5 | HPE H3C | JD117B | |
| 6 | Huawei | XFP-SX-MM850 | |
| 7 | Juniper | XFP-10G-S | |
| 8 | IBM | 40K8890 |
| Dell Compatible | 320-5164 | Vendor Name | HYTOPTODEVICE |
| Form Factor | XFP | Max Data Rate | 11.1Gbps |
| Wavelength | 850nm | Maxmum Transmission Distance | 300m |
| Connector | Duplex LC | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -6.5~-0.5dBm | Receiver Sensitivity | < -11.1dBm |
| Typical Power Consumption | ≤1.0W | Receiver Overload | -1dBm |
| Bit Error Ratio (BER) | 1E-12 | DDM/DOM | Support |
| Protocols | MSA Compliant, CPRI, eCPRI | Operation Temperature | 0to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC Multimode Fiber (MMF) — OM3 / OM4 (50/125 µm). Do NOT use SMF.
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Set speed to 10Gbps Full Duplex. Lock speed manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules: MSA hot-swappable. Insert/remove gently without powering down.
Environment: Commercial temperature (0°C to 70°C). Avoid extreme heat, moisture, and dust.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List and Supported Devices
Note: Use stable official Dell firmware for best compatibility.
Main Application Scenarios


Q1: What fiber type should buyers select for Dell 320-5164 compatible 10G XFP SR transceiver module? A: Yes, this 10G XFP SR transceiver requires multimode fiber. HYTOPTODEVICE compatible Dell 320-5164 runs up to 300m over OM3 MMF, 400m over OM4, only 33m over OM1 and 82m over OM2. Select OM3 or OM4 multimode patch cords for rack-to-rack data center links to achieve full rated transmission distance.
Q2: Can single-mode fiber be used with this 10G XFP SR optical module for data center interconnections? A: No, this 10G XFP SR transceiver cannot work over single-mode fiber. It adopts an 850nm VCSEL laser designed exclusively for multimode fiber. Signal cannot transmit normally over SMF, leading to no link or unstable signal. Choose XFP LR or XFP ER modules if long-distance single-mode transmission is required.
Q3: Will third-party compatible Dell 320-5164 modules trigger transceiver unsupported alarms on Dell switches? A: No, our pre-programmed module will not trigger unsupported transceiver alerts. HYTOPTODEVICE 10G XFP SR transceiver is factory flashed with Dell matching EEPROM profile. Insert it directly into Dell XFP ports, no extra configuration required, avoiding port disable warning on Dell legacy platforms.
Q4: What is DOM function on this 10G XFP SR transceiver and can network engineers check optical power readings? A: Yes, DOM is fully supported on this 10G XFP SR module. HYTOPTODEVICE Dell 320-5164 compatible transceiver complies with XFP MSA DOM standard. You can read real-time Tx power, Rx power and temperature via Dell CLI commands, helping engineers identify dirty fiber or bad connections before service outage.
Q5: Is hot swap available for 10G XFP SR transceiver module on powered Dell chassis switches and servers? A: Yes, hot swap is supported. The XFP form factor allows insertion and removal while the Dell device remains powered on. Each HYTOPTODEVICE 10G XFP SR transceiver meets XFP MSA hot-plug specification. Avoid frequent plug/unplug operations and protect LC port from dust to prevent intermittent link faults.
Q6: Does this 10G XFP SR transceiver auto negotiate down to 1G speed on Dell switch XFP ports? A: No, this 10G XFP SR module only runs at 10G rate. HYTOPTODEVICE compatible Dell 320-5164 follows 10GBASE-SR standard at 9.95~10.3125Gbps. You must manually set the Dell port to fixed 10G; auto negotiation to 1G will not work. Pick dedicated 1G optical modules for 1G fiber links.
Q7: Which MSA specification controls mechanical and electrical design for XFP 10G SR transceiver? A: XFP 10G SR transceiver follows XFP MSA INF-8077i specification. HYTOPTODEVICE Dell 320-5164 compatible module strictly complies with INF-8077i for mechanical dimensions, XFI electrical interface and DOM digital monitoring. Verify MSA compliance when sourcing third-party XFP optics for legacy Dell network deployment.
Q8: What temperature grades are available when purchasing HYTOPTODEVICE 10G XFP SR transceiver modules? A: We mainly supply commercial grade, and industrial grade is available upon request. Commercial grade works at 0℃ ~ +70℃, industrial grade covers -40℃ ~ +85℃. HYTOPTODEVICE 10G XFP SR transceiver commercial version fits standard indoor data center racks; choose industrial temperature modules for uncontrolled equipment rooms.
Q9: What transmission distance can be achieved with OM1 multimode fiber paired with Dell 320-5164 compatible module? A: OM1 fiber works but delivers a much shorter reach. HYTOPTODEVICE compatible 10G XFP SR transceiver only reaches 33 meters over OM1 62.5μm multimode fiber. Do not use OM1 fiber if your link distance exceeds 30m; upgrade to OM3 multimode cable to get full 300m performance.
Q10: What warranty coverage is offered for HYTOPTODEVICE Dell 320-5164 compatible modules? A: HYTOPTODEVICE compatible Dell 320-5164 carries 3-year factory warranty against manufacturing defects. The warranty covers hardware failure under rated operating conditions; it excludes damage caused by contaminated LC ports, ESD shock, improper handling or physical breakage. Submit RMA request to our support team if factory defects occur.
Q11: Can technicians rewrite EEPROM of XFP 10G SR transceiver onsite to fit other brand network hardware? A: Generally no, on-site EEPROM rewriting is not recommended. HYTOPTODEVICE 10G XFP SR transceiver is pre-programmed in factory with target brand EEPROM. If switching to non-Dell hardware, order pre-flashed modules for your new equipment; field programming requires professional tools and may permanently damage the module.
Q12: Why OEM original Dell 320-5164 modules carry higher pricing than compatible alternatives? A: OEM original XFP modules include heavy brand markup. Dell original 320-5164 price contains brand licensing and hardware lock-in cost, while core optical component cost stays similar. HYTOPTODEVICE compatible 10G XFP SR transceiver is MSA compliant, pre-programmed drop-in replacement with factory bulk price for integrators and volume buyers.
Q13: Is stocking spare 10G XFP SR modules a good practice for legacy Dell production networks? A: Yes, keeping spare inventory for Dell 320-5164 is highly recommended for legacy Dell production networks. XFP hardware is end-of-life, OEM stock is limited and lead time is long. HYTOPTODEVICE maintains ready stock for bulk orders; keep spare 10G XFP SR transceiver on hand to quickly replace faulty units and minimize data center downtime.
Q14: How to check received optical power after inserting Dell 320-5164 compatible XFP module into Dell switch? A: Yes, real-time optical readings can be checked via Dell CLI. After inserting HYTOPTODEVICE compatible 10G XFP SR transceiver, run show interfaces transceiver command. Confirm Rx power stays between -9.9 ~ -1.0 dBm; clean LC connector or re-terminate multimode fiber if the value falls outside this range before enabling the port.
Q15: Is 10G XFP SR transceiver suitable for leaf-spine data center rack interconnection projects? A: Yes, 10G XFP SR transceiver is ideal for leaf-spine rack interconnection within data centers. It supports 300m over OM3 multimode fiber with low latency. HYTOPTODEVICE Dell 320-5164 compatible modules are widely deployed for legacy leaf-spine architecture; confirm fiber type and link length before field installation.
Q16: What risks come with low-cost unbranded XFP 10G SR transceivers for data center network projects? A: Low-cost unbranded XFP optics bring multiple operational risks. Uncalibrated VCSEL lasers, inaccurate DOM readings, incomplete MSA compliance, insufficient aging test and high early failure rate. HYTOPTODEVICE 10G XFP SR transceiver passes 72-hour burn-in test; avoid untested generic modules for production data center multimode links.
Packaging & Custom OEM Solutions
Individually sealed in ESD-safe packaging and ready to ship. We offer tailored OEM solutions—including custom logos and private labeling—to support high-volume distributors,wholesaler and system integrators.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE XFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



