| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | XFP-10G-MM-SR | |
| 2 | Dell | 320-5164 | |
| 3 | H3C | XFP-SX-MM850 | |
| 4 | HPE BladeSystem | 443756-B21 | |
| 5 | HPE H3C | JD117B | |
| 6 | Huawei | XFP-SX-MM850 | |
| 7 | Juniper | XFP-10G-S | |
| 8 | IBM | 40K8890 |
| Cisco Compatible | XFP-10G-MM-SR | Vendor Name | HYTOPTODEVICE |
| Form Factor | XFP | Max Data Rate | 11.1Gbps |
| Wavelength | 850nm | Maxmum Transmission Distance | 300m |
| Connector | Duplex LC | Transmitter Type | VCSEL 850nm |
| Cable Type | MMF | Receiver Type | PIN |
| TX Power | -6.5~-0.5dBm | Receiver Sensitivity | < -11.1dBm |
| Typical Power Consumption | ≤1.0W | Receiver Overload | -1dBm |
| Bit Error Ratio (BER) | 1E-12 | DDM/DOM | Support |
| Protocols | MSA Compliant, CPRI, eCPRI | Operation Temperature | 0to 70°C (32 to 158°F) |
For detailed technical specifications, please refer to the Datasheet
Usage Guidelines & Best Practices
Fiber Choice: Duplex LC Multimode Fiber (MMF) — OM3 / OM4 (50/125 µm). Do NOT use SMF.
Connector Match: UPC/PC polish only. Do NOT use APC.
Cleanliness & Dust: Keep dust caps on whenever unattached. Clean fiber end-faces with a optical cleaning pen before insertion; dust causes over 80% of optical link failures.
Link Setup:Set speed to 10Gbps Full Duplex. Lock speed manually if auto-negotiation fails.
Handling: Wear ESD protection. Keep fiber bend radius ≥ 30 mm.
Installation & Hot-Swap Rules: MSA hot-swappable. Insert/remove gently without powering down.
Environment: Commercial temperature (0°C to 70°C). Avoid extreme heat, moisture, and dust.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List and Supported Devices
Lab validated with Cisco tuned EEPROM, plug and play for Cisco XFP interface hardware.
Note: Use stable official Cisco IOS firmware for best compatibility.
Main Application Scenarios


Q1:What fiber cable type works for Cisco XFP-10G-MM-SR compatible 10G XFP SR transceiver module? A:Yes, this 10G XFP SR transceiver requires multimode fiber. HYTOPTODEVICE compatible XFP-10G-MM-SR runs up to 300m over OM3 MMF, 400m over OM4, only 33m over OM1 and 82m over OM2. Select OM3 or OM4 multimode patch cords for your rack-to-rack data center links to achieve the full rated transmission distance.
Q2:Can I use single-mode fiber with this 10G XFP SR optical module for data center links? A:No, this 10G XFP SR transceiver cannot work over single-mode fiber. It uses 850nm VCSEL laser designed exclusively for multimode fiber. Signal cannot transmit normally over SMF, and you will get no link or unstable signal. Choose XFP LR or XFP ER modules if you need single-mode long-distance transmission.
Q3:Will third-party compatible XFP-10G-MM-SR modules trigger transceiver unsupported alarms on Cisco IOS switches? A:No, our pre-programmed module will not trigger unsupported transceiver alerts. HYTOPTODEVICE 10G XFP SR transceiver is factory flashed with Cisco matching EEPROM profile. Insert it directly into Cisco XFP ports, no extra CLI configuration required, avoid port disable warning on Catalyst and Nexus legacy platforms.
Q4:What is DOM function on 10G XFP SR transceiver module and can engineers read optical power data? A:Yes, DOM is fully supported on this 10G XFP SR module. HYTOPTODEVICE XFP-10G-MM-SR compatible transceiver follows XFP MSA DOM standard. You can read real-time Tx power, Rx power and temperature via Cisco IOS show commands, helping engineers diagnose fiber dirty or connection issues before service failure.
Q5:Is hot swap available for 10G XFP SR transceiver module on running Cisco chassis switches? A:Yes, hot swap is supported. The XFP form factor allows insertion and removal while the switch remains powered on. Each HYTOPTODEVICE 10G XFP SR transceiver complies with XFP MSA hot-plug specification. But avoid frequent plug/unplug operations and protect the LC port from dust to prevent intermittent link issues.
Q6:Does 10G XFP SR module support auto negotiation down to 1G speed on Cisco switch ports? A:No, this 10G XFP SR module only works at 10G rate. HYTOPTODEVICE compatible XFP-10G-MM-SR is 10GBASE-SR standard transceiver running 9.95~10.3125Gbps. You must manually set the Cisco port to fixed 10G; auto negotiation to 1G will not work, select separate 1G optical modules for 1G fiber links.
Q7:What MSA standard defines the mechanical and electrical specs of XFP 10G SR transceiver? A:XFP 10G SR transceiver follows XFP MSA INF-8077i specification. HYTOPTODEVICE XFP-10G-MM-SR compatible module strictly complies with INF-8077i for mechanical dimension, XFI electrical interface and DOM digital monitoring. Verify MSA compliance when sourcing third-party XFP optics for legacy Cisco network deployment.
Q8:What operating temperature grades can buyers choose when ordering 10G XFP SR transceiver modules? A:We mainly supply commercial grade, and industrial grade is available on request. Commercial grade works at 0℃ ~ +70℃, industrial grade covers -40℃ ~ +85℃. HYTOPTODEVICE 10G XFP SR transceiver commercial version fits standard indoor data center racks; pick industrial temperature modules for uncontrolled equipment room environments.
Q9:What maximum transmission distance can I get if I use OM1 multimode fiber with XFP-10G-MM-SR module? A:Yes, OM1 fiber can work but reach will be much shorter. HYTOPTODEVICE compatible 10G XFP SR transceiver only reaches 33 meters over OM1 62.5μm multimode fiber. Do not use OM1 fiber if your link distance exceeds 30m, upgrade to OM3 multimode cable to get full 300m performance.
Q10:What warranty terms are provided for HYTOPTODEVICE compatible Cisco XFP-10G-MM-SR modules? A:HYTOPTODEVICE compatible XFP-10G-MM-SR carries 3-year factory warranty against manufacturing defects. The warranty covers hardware failure under rated operating conditions; it excludes damage caused by dust-contaminated LC ports, ESD shock, improper handling or physical breakage. Submit RMA request to our support team if factory defects occur.
Q11:Can technicians rewrite EEPROM of XFP 10G SR transceiver on site to match other vendor network hardware? A:Generally no, on-site EEPROM rewriting is not recommended. HYTOPTODEVICE 10G XFP SR transceiver is pre-programmed in factory with target brand EEPROM. If you switch to non-Cisco hardware, order pre-flashed modules for your new equipment; field programming requires professional tools and may damage the module permanently.
Q12:Why original Cisco XFP-10G-MM-SR modules have much higher pricing than compatible alternatives? A:OEM original XFP modules carry heavy brand markup. Cisco original XFP-10G-MM-SR price includes brand licensing and hardware lock-in cost, while optical component cost is similar. HYTOPTODEVICE compatible 10G XFP SR transceiver is MSA compliant, pre-programmed drop-in replacement with factory bulk price for integrators and volume buyers.
Q13:Is it wise to stock spare 10G XFP SR modules for legacy Cisco production networks? A:Yes, keeping spare inventory for XFP-10G-MM-SR is highly recommended for legacy Cisco production networks. XFP hardware is end-of-life, OEM stock is limited and lead time is long. HYTOPTODEVICE maintains ready stock for bulk orders; keep spare 10G XFP SR transceiver on hand to quickly replace faulty units and minimize data center downtime.
Q14:How to verify the received optical power after inserting XFP-10G-MM-SR module into Cisco switch? A:Yes, you can check real-time optical readings via Cisco IOS CLI. After inserting HYTOPTODEVICE compatible 10G XFP SR transceiver, run show interfaces transceiver command. Confirm Rx power stays between -9.9 ~ -1.0 dBm; clean LC connector or re-terminate multimode fiber if the value falls outside this range before enabling the port.
Q15:Is 10G XFP SR transceiver suitable for leaf-spine data center rack interconnection? A:Yes, 10G XFP SR transceiver is ideal for leaf-spine rack interconnection within data centers. It supports 300m over OM3 multimode fiber with low latency. HYTOPTODEVICE XFP-10G-MM-SR compatible modules are widely used for legacy leaf-spine architecture; confirm fiber type and link length before deployment.
Packaging & Custom OEM Solutions
Individually sealed in ESD-safe packaging and ready to ship. We offer tailored OEM solutions—including custom logos and private labeling—to support high-volume distributors,wholesaler and system integrators.
Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE XFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.



