| NO. | Brand | Compatible P/N | Transceiver Type |
| 1 | Cisco | QSFP-4X10G-AOC30M | |
| 2 | Arista Networks | QSFP-4X10G-AOC30M | |
| 3 | Dell | CBL-QSFP-4X10G-AOC30M | |
| 4 | Juniper Networks | JNP-QSFP-AOCBO-30M | |
| 5 | Extreme | 10GB-4-F30-QSFP | |
| 6 | H3C | QSFP-4X10G-D-AOC-30M | |
| 7 | Brocade | 40G-QSFP-4SFP-AOC-3001 |
| Arista Compatible |
QSFP-4X10G-AOC30M
|
Vendor Name | HYTOPTODEVICE |
| Connector | QSFP+ to 4 SFP+ | Max Data Rate | 40Gbps |
| Operating Wavelength | 850nm | Fiber Cable | OM3 MMF |
| Cable Length | 30m (98ft) | Power Consumption | ≤1.4W |
| Jacket Material | OFNP | Operation Temperature | 0~ 70 °C (32 to 158°F) |
| Minimum Bend Radius | 30mm | Protocols | 10G/40Gigabit Ethernet or Fibre Channel |
| Application |
InfinibandQDR/DDR/SDR,40G Ethernet,Data Center,Fibre
Channel
|
Warranty | 5 Years |
Usage Guidelines & Best Practices
Mandatory Port Breakout Configuration: Ensure the host QSFP+ port supports channelization. Enable breakout mode (4x10G) via the switch CLI before connecting the cable.
Cabling Requirements: Do not exceed the minimum 30mm bend radius, avoid sharp folding, heavy extrusion or long-term tension on the cable assembly.
Port Installation Standard: Do not mix this breakout AOC with straight QSFP+ to QSFP+ AOC configuration.
Hot‑swap rule:Never pull or tug directly on the individual breakout legs. Always use the integrated pull-tab or bale latch when inserting or removing connectors.
Operating Environment: 0‑70℃, indoor cabinet deployment only.
For detailed operation instructions, please refer to the User Guide.
Full Compatibility List & Supported Devices
Built on MSA open standards, this 40G QSFP+ BREAKOUT active optical cable supports mixed-vendor networking devices. can interoperate with mainstream network brands including Arista, Brocade, Juniper, Dell, H3C and Fortinet, for mixed-vendor rack stacking and server fabric expansion.




Q1: What bend protection rules should I follow when routing the four breakout pigtails of this 30m Arista breakout AOC? A: Always keep the bend radius above approximately 30mm. Excessively sharp bends will fracture internal glass fibers and permanently break the link of this 40G QSFP+ BREAKOUT active optical cable from our manufacturer.
Q2: Can this Arista compatible breakout AOC deliver full bidirectional 40Gbps aggregate throughput across all four 10G lanes? A: Yes, it supports full wire-speed 40Gbps bidirectional transmission, with four independent 10G channels running at full speed without bandwidth reduction.
Q3: Will the full 30-meter cable span create signal jitter and undermine optical link stability? A: No. Built-in CDR circuits inside optical transceivers actively suppress jitter and maintain an ultra-low bit error rate for reliable long-distance data transmission.
Q4: Can I set different operating speeds separately for each SFP+ breakout tail on this fanout AOC? A: No. The 40G QSFP+ input port is fixed to four 10G channels. Individual breakout ports cannot be configured for 1G or 25G operation.
Q5: What switch alert messages indicate an EEPROM coding mismatch on this Arista compatible breakout AOC? A: Typical warning logs include "Unsupported transceiver detected", "Security checksum error", or "Unqualified optic detected", which signal incorrect vendor programming.
Q6: Are these 10G SFP+ breakout tails compatible with older 1G SFP ports on legacy network switches? A: No. SFP+ hardware is engineered for native 10G operation and cannot auto-negotiate down to 1G SFP port speeds.
Q7: What result will appear if I plug the main QSFP+ connector into a 100G QSFP28 port by mistake? A: QSFP+ follows 40G electrical specifications. It cannot build a stable link inside a native 100G QSFP28 port without dedicated down-conversion adapters.
Q8: Which Arista CLI commands help confirm all four breakout sub-channels are correctly recognized? A: You can run commands such as show interfaces status or show inventory to verify all four breakout sub-interfaces show up in the port inventory.
Q9: Can I daisy-chain multiple breakout AOCs together to extend the overall cabling reach for my data center project? A: No. Active optical breakout cables cannot be cascaded. Series connection breaks the optical path and causes total link failure.
Q10: What troubleshooting checks should I run when only three breakout lanes come online after installation? A: Verify the Arista switch breakout configuration, reseat each SFP+ connector firmly, and analyze DOM diagnostic data to pinpoint the faulty lane.
Q11: Will heavy pressure or accidental foot traffic damage the internal fiber strands inside this breakout AOC? A: Yes. Crushing force can crack internal glass fibers. The outer jacket may remain intact while the optical transmission path is permanently destroyed.
Q12: Does this 30m long breakout AOC add heavy weight and cause port sag on Arista switch slots? A: No. AOC fanout cables are far lighter than copper breakout alternatives, eliminating mechanical strain and port sag issues on switch hardware.
Q13: Is on-site splicing or field repair possible if the cable jacket gets pinched or cut during rack installation? A: No. Transceivers are pre-integrated into the cable assembly. Field splicing is not feasible, and damaged AOC units require full replacement.
Q14: What support can I get if bulk breakout AOC shipments arrive with incorrect vendor EEPROM coding? A: As your 40G QSFP+ BREAKOUT active optical cable manufacturer, HYTOPTODEVICE provides exchange, return or re-programming service for coding compatibility issues upon delivery.
Q15: Can I order custom non-standard lengths instead of standard stocked sizes for large enterprise procurement? A: Standard lengths including 1m,3m,5m,10m,15m,20m,30m,50m are kept in stock. Custom lengths are available for enterprise orders subject to MOQ terms.
Packaging & Custom OEM Solutions
ESD Protection & Fast Shipping: Every transceiver is sealed in an ESD-safe bag and ready for same-day dispatch from stock.
Custom OEM & Branding: We provide logo printing, private labeling, and custom packaging to help distributors and integrators build their brand—no factory investment required.

Why Network Engineers Choose HYTOPTODEVICE
HYTOPTODEVICE has supplied over 5000,000 optical transceiver modules to data centers, ISPs, and enterprise networks across 100+ countries since 2011. Every module undergoes a 72-hour burn-in test and full DDM/DOM validation before shipment.
“Phenomenal performance. We deployed 200 HYTOPTODEVICE SFP modules to replace Cisco OEMs in our backbone network. Result? Zero compatibility issues and a 60% reduction in costs. Highly recommended for mission-critical networks."— Senior Network Engineer, Regional Telecom, Australia
Quality Certification & Compliance
At HYTOPTODEVICE, our quality commitment is backed by industry-standard validations. From fiber optical transceiver manufacturing to final visual inspection, from IQC、IPQC、FQC to OQC, our processes ensure global compliance and reliability.
We adhere to rigorous standards for our SFP modules and network solutions:
ISO 9001: Certified quality management and production consistency.
CE & FCC: Fully compliant for seamless Global Market Access.
RoHS: Committed to environmental responsibility and hazardous material control.
Proven Reliability: Rigorous testing to reduce compliance risk and ensure safety.
Certified Quality. Global Standards. Guaranteed Performance.





